HP NetServer LXr Pro8 HP Netserver E 60, LC 3, LH 3/3r, and LPr Processor Upgr - Page 50

Replace the Cover

Get HP NetServer LXr Pro8 PDF manuals and user guides View all HP NetServer LXr Pro8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Chapter 4 Installation in E 60 and LPr 2. Insert the terminator board into the secondary processor position. 3. Verify that the terminator board is installed completely in the slot. Setting System Switches After installing processors, verify that the system switches are set to the correct processor clock speed (frequency). If the switches are not set correctly, set them accordingly. To set the system switches: 1. Locate the system switches on the system board (see Figure 4-1 or 4-2). 2. Look up the appropriate switch settings for the speed (frequency) of the processor modules installed in the NetServer. Tables of system switch settings are located next to the system switches and on the Technical Reference Card. 3. Set the switches accordingly. CAUTION Processor modules are designed to operate at the speed that is printed on the module. Do not set the processor speed switches to a different speed. Setting the processor speed to another speed may result in unreliable or intermittent performance. Data integrity may also be placed at risk if processors are operated at speeds other than that specified on the processor module. Replace the Cover NOTE In an HP NetServer E 60, reposition the cooling duct over the processor modules, and snap it into place. 1. Reinstall any accessory boards that you removed. 2. Replace the cover. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Chapter 4
Installation in E 60 and LPr
46
2.
Insert the terminator board into the secondary processor position.
3.
Verify that the terminator board is installed completely in the slot.
Setting System Switches
After installing processors, verify that the system switches are set to the correct
processor clock speed (frequency). If the switches are not set correctly, set them
accordingly.
To set the system switches:
1.
Locate the system switches on the system board (see Figure 4-1 or 4-2).
2.
Look up the appropriate switch settings for the speed (frequency) of the
processor modules installed in the NetServer. Tables of system switch
settings are located next to the system switches and on the Technical
Reference Card.
3.
Set the switches accordingly.
CAUTION
Processor modules are designed to operate at the speed that is
printed on the module. Do not set the processor speed
switches to a different speed. Setting the processor speed to
another speed may result in unreliable or intermittent
performance. Data integrity may also be placed at risk if
processors are operated at speeds other than that specified on
the processor module.
Replace the Cover
NOTE
In an HP NetServer E 60, reposition the cooling duct over the
processor modules, and snap it into place.
1.
Reinstall any accessory boards that you removed.
2.
Replace the cover.