HP Omni Pro 110 Maintenance and Service Guide: HP Omni Pro 110 All-in-One PC - Page 60

System Board Shield

Get HP Omni Pro 110 PDF manuals and user guides View all HP Omni Pro 110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

System Board Shield The system board shield sits above the system board. It is secured with two screws. To remove the system board shield: 1. Prepare the computer for disassembly (see Preparing to Disassemble the Computer on page 28). 2. Remove the small rear cover (see Small Rear Cover on page 29). 3. Remove the stand (see Stand on page 30). 4. Remove the right rear cover (see Right Rear Cover on page 36). 5. Remove the heat sink (see Heat Sink (Thermal Module) on page 39). 6. Remove the rear cover (see Rear Cover on page 47). 7. Remove the two screws (1) that secure the shield to the computer. 8. Rotate the shield from left to right to remove it from the computer (2). Figure 7-23 Removing the system board shield To install the system board shield, reverse the removal procedures. 52 Chapter 7 Removal and Replacement Procedures All-in One (AIO) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
System Board Shield
The system board shield sits above the system board. It is secured with two screws.
To remove the system board shield:
1.
Prepare the computer for disassembly (see
Preparing to Disassemble the Computer
on page
28
).
2.
Remove the small rear cover (see
Small Rear Cover
on page
29
).
3.
Remove the stand (see
Stand
on page
30
).
4.
Remove the right rear cover (see
Right Rear Cover
on page
36
).
5.
Remove the heat sink (see
Heat Sink (Thermal Module)
on page
39
).
6.
Remove the rear cover (see
Rear Cover
on page
47
).
7.
Remove the two screws
(1)
that secure the shield to the computer.
8.
Rotate the shield from left to right to remove it from the computer
(2)
.
Figure 7-23
Removing the system board shield
To install the system board shield, reverse the removal procedures.
52
Chapter 7
Removal and Replacement Procedures All-in One (AIO) Chassis