Home » IBM Manuals » Desktops » IBM 88614RX » Manual Viewer

IBM 88614RX Maintenance Manual - Page 121

Fan X Outside Recommended Speed, Internal Error CPU X Fault

UPC - 000435172662

Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

Note: See Chapter 7, "Parts listing, Types 8861, 8862," on page 139 to determine which components are replaceable by the customer and which components must be replaced by an IBM field service technician. Service Processor message FRU/action Fan X Failure (X of 1-6 = individual fans 1 1. Verify no obstacles are blocking or inserted into the fan or through 6; X of 7=power supply 1; X of 8=power power supply. supply 2.) 2. Check the physical connection and verify fan or power supply is properly seated. 3. Replace component X: a. Where X = a number from 1 through 6, replace fan X. b. Where X = 7 or 8, replace power supply X. Fan X not detected (X of 1-6 = individual fans 1 through 6; X of 7=power supply 1; X of 8=power supply 2.) 1. Verify no obstacles are blocking or inserted into the fan or power supply. 2. Check the physical connection and verify fan or power supply is properly seated. 3. Replace component X: a. Where X = a number from 1 through 6, replace fan X. b. Where X = 7 or 8, replace power supply X. Fan X Outside Recommended Speed (X of 1-6 = individual fans 1 through 6; X of 7=power supply 1; X of 8=power supply 2.) 1. Verify no obstacles are blocking or inserted into the fan or power supply. 2. Check the physical connection and verify fan or power supply is properly seated. 3. Replace component X: a. Where X = a number from 1 through 6, replace fan X. b. Where X = 7 or 8, replace power supply X. Front Panel is not plugged in 1. Verify operator panel cables are properly connected (verify LED activity). 2. Replace operator information panel. Hard Drive X Fault 1. Run diagnostics. 2. Hard disk drive. 3. ServeRAID adapter. 4. SCSI backplane. Hard drive X removal detected v Re-insert hard disk drive X and restart server. Hostname set to by user v Information only Hot plug card is not plugged in 1. Verify PCI cabling. 2. Failing hot plug cable/card. Integrated Systems Management Processor 1. Remove ac power from the server and restart the server encountered failures upon starting 2. Run diagnostics. Internal Error CPU X Fault v Microprocessor X Internal SCSI cable is not plugged in 1. Verify SCSI cables are properly connected. 2. SCSI backplane. Invalid CPU configuration v Verify that microprocessors have been installed in the correct order (see "Installing a microprocessor" on page 44). Invalid Fan configuration v Replace any missing or failed fans. Chapter 6. Symptom-to-FRU index 111

Section	Page
About this manual	5
Important safety information	5
Online support	5
Contents	7
Chapter 1. Introduction	11
Related publications	11
Notices and statements used in this publication	12
Features and specifications	13
Server controls, LEDs, and power	14
Front view	14
Rear view	16
Light path diagnostics LED panel	18
Server power features	18
Turning on the server	18
Turning off the server	19
Chapter 2. Configuring the server	21
Using the Configuration/Setup Utility program	21
Using the ServerGuide Setup and Installation CD	22
Using the PXE boot agent utility program	22
Using the RAID configuration programs	23
Updating the integrated service processor firmware	23
Configuring the Gigabit Ethernet controllers	23
Remote Supervisor Adapter II	23
Chapter 3. Diagnostics	25
General checkout	25
Diagnostic tools overview	27
POST error logs	27
Viewing error logs from the Configuration/Setup Utility program	27
Viewing error logs from the diagnostic programs	28
Light path diagnostics	28
Microprocessor LEDs	29
DIMM LEDs	30
Remind button	31
Diagnostic programs and error messages	32
Diagnostic text messages	32
Starting the diagnostic programs	33
Viewing the test log	33
Viewing the system-error log	34
Recovering BIOS code	34
Password override jumper	35
Forcing a power-on	36
Power checkout	37
Ethernet controller troubleshooting	37
Chapter 4. Installing options	39
Installation guidelines	39
System reliability guidelines	39
Working inside a server with power on	40
Handling static-sensitive devices	40
Major components of the xSeries 365 server	41
Removing the cover and bezel	42
PCI or PCI-X adapters	43
Installing a PCI or PCI-X adapter	45
Removing a PCI or PCI-X adapter	46
Installing a hot-swap hard disk drive	46
Replacing the CD-ROM drive	48
Memory modules	49
DIMM banks and ports	50
DIMM installation	51
Installing a microprocessor	54
Installing a hot-swap power supply	61
Replacing the battery	63
Replacing a hot-swap fan	65
Replacing the memory cassette	66
Completing the installation	68
Installing the cover and bezel	68
Connecting the cables	69
RXE connector cabling	70
Gigabit Ethernet cabling	70
Updating the server configuration	70
I/O connectors	71
Server connectors	72
Remote Supervisor Adapter II connectors	72
Ethernet connector	73
Universal Serial Bus connector	73
RXE Expansion Port connector	74
Auxiliary-device (pointing device) connector	74
Keyboard connector	74
Serial connector	74
RXE Management Port connector	74
Power supply connector	75
SCSI connector	75
Chapter 5. FRU information (service only)	77
Microprocessor tray assembly	78
Microprocessor board connectors, jumpers and LEDs	78
Microprocessor removal	78
Thermal grease	79
Diskette drive	81
Operator information panel	82
Media interposer card	83
SCSI backplane	84
PCI switch card assembly	86
Adapter retainer bracket assembly	87
Power-supply structure	88
I/O board and power backplane assembly	89
I/O board connectors	89
I/O board LEDs	90
I/O board switches and jumpers	90
Replacing the I/O board and power backplane assembly	91
Chapter 6. Symptom-to-FRU index	95
Beep symptoms	96
No beep symptoms	97
POST error codes	98
Light path LED errors	103
Diagnostic error codes	105
System-error log entries	115
SMI handler messages	116
Service processor messages	119
Error symptoms	131
Power LED errors	140
SCSI error messages	142
ServeRAID (ISPR) error procedures	142
ServeRAID error codes	144
Undetermined problems	146
Problem-determination tips	147
Chapter 7. Parts listing, Types 8861, 8862	149
System	150
Keyboard CRUs	151
Power cord FRUs	152
Appendix A. Getting help and technical assistance	155
Before you call	155
Using the documentation	155
Getting help and information from the World Wide Web	155
Software service and support	156
Hardware service and support	156
Appendix B. Related service information	157
Safety information	157
General safety	157
Electrical safety	158
Safety inspection guide	159
Handling electrostatic discharge-sensitive devices	160
Grounding requirements	160
Safety notices (multilingual translations)	160
Appendix C. Notices	201
Edition notice	201
Trademarks	202
Important notes	202
Product recycling and disposal	203
Battery return program	203
Electronic emission notices	204
Federal Communications Commission (FCC) statement	204
Industry Canada Class A emission compliance statement	204
Australia and New Zealand Class A statement	204
United Kingdom telecommunications safety requirement	204
European Union EMC Directive conformance statement	205
Taiwanese Class A warning statement	205
Chinese Class A warning statement	205
Japanese Voluntary Control Council for Interference (VCCI) statement	205
Index	207
A	207
B	207
C	207
D	207
E	207
F	207
G	207
H	208
I	208
K	208
L	208
M	208
N	208
O	208
P	208
R	209
S	209
T	209
U	209
V	209

Match case Limit results 1 per page

Note: See Chapter 7, “Parts listing, Types 8861, 8862,” on page 139 to determine which components are

replaceable by the customer and which components must be replaced by an IBM field service technician.

Service Processor message

FRU/action

Fan X Failure

(X of 1-6 = individual fans 1

through 6; X of 7=power supply 1; X of 8=power

supply 2.)

Verify no obstacles are blocking or inserted into the fan or

power supply.

Check the physical connection and verify fan or power supply

is properly seated.

Replace component X:

Where X = a number from 1 through 6, replace fan X.

Where X = 7 or 8, replace power supply X.

Fan X not detected

(X of 1-6 = individual fans

1 through 6; X of 7=power supply 1; X of

8=power supply 2.)

Verify no obstacles are blocking or inserted into the fan or

power supply.

Check the physical connection and verify fan or power supply

is properly seated.

Replace component X:

Where X = a number from 1 through 6, replace fan X.

Where X = 7 or 8, replace power supply X.

Fan X Outside Recommended Speed

(X of

1-6 = individual fans 1 through 6; X of 7=power

supply 1; X of 8=power supply 2.)

Verify no obstacles are blocking or inserted into the fan or

power supply.

Check the physical connection and verify fan or power supply

is properly seated.

Replace component X:

Where X = a number from 1 through 6, replace fan X.

Where X = 7 or 8, replace power supply X.

Front Panel is not plugged in

Verify operator panel cables are properly connected (verify

LED activity).

Replace operator information panel.

Hard Drive X Fault

Run diagnostics.

Hard disk drive.

ServeRAID adapter.

SCSI backplane.

Hard drive X removal detected

Re-insert hard disk drive X and restart server.

Hostname set to <value> by user <USERID>

Information only

Hot plug card is not plugged in

Verify PCI cabling.

Failing hot plug cable/card.

Integrated Systems Management Processor

encountered failures upon starting

Remove ac power from the server and restart the server

Run diagnostics.

Internal Error CPU X Fault

Microprocessor X

Internal SCSI cable is not plugged in

Verify SCSI cables are properly connected.

SCSI backplane.

Invalid CPU configuration

Verify that microprocessors have been installed in the

correct order (see “Installing a microprocessor” on page

44).

Invalid Fan configuration

Replace any missing or failed fans.

Chapter 6. Symptom-to-FRU index

111