Home » IBM Manuals » Desktops » IBM 88614RX » Manual Viewer

IBM 88614RX Maintenance Manual - Page 59

so can damage the microprocessor pins. Loosening one captive screw fully

UPC - 000435172662

Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Attention: You must ensure that the locking lever on the microprocessor socket is in the fully-open position before you insert the microprocessor in the socket. Failure to do so might result in permanent damage to the microprocessor, microprocessor socket, and microprocessor-tray assembly. 10. Install the microprocessor: a. Touch the static-protective package containing the new microprocessor to any unpainted metal surface on the server; then, remove the microprocessor from the package. b. Position the microprocessor over the microprocessor connector as shown in the following illustration. Carefully press the microprocessor into the socket. Attention: To avoid bending the pins on the microprocessor, do not use excessive force when pressing it into the socket. Microprocessor Microprocessor orientation indicator Microprocessor connector Microprocessorrelease lever 11. Close the microprocessor-release lever to secure the microprocessor. Attention: v Do not disturb or contaminate the thermal material on the bottom of the new heat sink. Doing so damages its heat-conducting capability and exposes the new microprocessor to overheating. v If you need to remove the heat sink after installing it, note that the thermal material might have formed a strong bond between the heat sink and the microprocessor. Do not force the heat sink and microprocessor apart; doing so can damage the microprocessor pins. Loosening one captive screw fully before loosening the other captive screw helps break the bond between the components without damaging them. 12. Remove the heat sink from its package and remove the cover from the bottom of the heat sink. Make sure that the thermal material is still on the bottom of the heat sink. Remove the release liner and orient the heat sink above the microprocessor; then, press the heat sink into place. Press firmly on the captive screws and tighten them, alternating between screws until they are tight. Do not overtighten the screws. 13. If you installed microprocessor 3 or 4, install the VRM in the associated VRM socket. a. Open the retaining clips at either end of the VRM connector. Attention: To avoid breaking the VRM retaining clips or damaging the VRM connectors, open and close the clips gently. Chapter 4. Installing options 49

Section	Page
About this manual	5
Important safety information	5
Online support	5
Contents	7
Chapter 1. Introduction	11
Related publications	11
Notices and statements used in this publication	12
Features and specifications	13
Server controls, LEDs, and power	14
Front view	14
Rear view	16
Light path diagnostics LED panel	18
Server power features	18
Turning on the server	18
Turning off the server	19
Chapter 2. Configuring the server	21
Using the Configuration/Setup Utility program	21
Using the ServerGuide Setup and Installation CD	22
Using the PXE boot agent utility program	22
Using the RAID configuration programs	23
Updating the integrated service processor firmware	23
Configuring the Gigabit Ethernet controllers	23
Remote Supervisor Adapter II	23
Chapter 3. Diagnostics	25
General checkout	25
Diagnostic tools overview	27
POST error logs	27
Viewing error logs from the Configuration/Setup Utility program	27
Viewing error logs from the diagnostic programs	28
Light path diagnostics	28
Microprocessor LEDs	29
DIMM LEDs	30
Remind button	31
Diagnostic programs and error messages	32
Diagnostic text messages	32
Starting the diagnostic programs	33
Viewing the test log	33
Viewing the system-error log	34
Recovering BIOS code	34
Password override jumper	35
Forcing a power-on	36
Power checkout	37
Ethernet controller troubleshooting	37
Chapter 4. Installing options	39
Installation guidelines	39
System reliability guidelines	39
Working inside a server with power on	40
Handling static-sensitive devices	40
Major components of the xSeries 365 server	41
Removing the cover and bezel	42
PCI or PCI-X adapters	43
Installing a PCI or PCI-X adapter	45
Removing a PCI or PCI-X adapter	46
Installing a hot-swap hard disk drive	46
Replacing the CD-ROM drive	48
Memory modules	49
DIMM banks and ports	50
DIMM installation	51
Installing a microprocessor	54
Installing a hot-swap power supply	61
Replacing the battery	63
Replacing a hot-swap fan	65
Replacing the memory cassette	66
Completing the installation	68
Installing the cover and bezel	68
Connecting the cables	69
RXE connector cabling	70
Gigabit Ethernet cabling	70
Updating the server configuration	70
I/O connectors	71
Server connectors	72
Remote Supervisor Adapter II connectors	72
Ethernet connector	73
Universal Serial Bus connector	73
RXE Expansion Port connector	74
Auxiliary-device (pointing device) connector	74
Keyboard connector	74
Serial connector	74
RXE Management Port connector	74
Power supply connector	75
SCSI connector	75
Chapter 5. FRU information (service only)	77
Microprocessor tray assembly	78
Microprocessor board connectors, jumpers and LEDs	78
Microprocessor removal	78
Thermal grease	79
Diskette drive	81
Operator information panel	82
Media interposer card	83
SCSI backplane	84
PCI switch card assembly	86
Adapter retainer bracket assembly	87
Power-supply structure	88
I/O board and power backplane assembly	89
I/O board connectors	89
I/O board LEDs	90
I/O board switches and jumpers	90
Replacing the I/O board and power backplane assembly	91
Chapter 6. Symptom-to-FRU index	95
Beep symptoms	96
No beep symptoms	97
POST error codes	98
Light path LED errors	103
Diagnostic error codes	105
System-error log entries	115
SMI handler messages	116
Service processor messages	119
Error symptoms	131
Power LED errors	140
SCSI error messages	142
ServeRAID (ISPR) error procedures	142
ServeRAID error codes	144
Undetermined problems	146
Problem-determination tips	147
Chapter 7. Parts listing, Types 8861, 8862	149
System	150
Keyboard CRUs	151
Power cord FRUs	152
Appendix A. Getting help and technical assistance	155
Before you call	155
Using the documentation	155
Getting help and information from the World Wide Web	155
Software service and support	156
Hardware service and support	156
Appendix B. Related service information	157
Safety information	157
General safety	157
Electrical safety	158
Safety inspection guide	159
Handling electrostatic discharge-sensitive devices	160
Grounding requirements	160
Safety notices (multilingual translations)	160
Appendix C. Notices	201
Edition notice	201
Trademarks	202
Important notes	202
Product recycling and disposal	203
Battery return program	203
Electronic emission notices	204
Federal Communications Commission (FCC) statement	204
Industry Canada Class A emission compliance statement	204
Australia and New Zealand Class A statement	204
United Kingdom telecommunications safety requirement	204
European Union EMC Directive conformance statement	205
Taiwanese Class A warning statement	205
Chinese Class A warning statement	205
Japanese Voluntary Control Council for Interference (VCCI) statement	205
Index	207
A	207
B	207
C	207
D	207
E	207
F	207
G	207
H	208
I	208
K	208
L	208
M	208
N	208
O	208
P	208
R	209
S	209
T	209
U	209
V	209

Match case Limit results 1 per page

Attention:

You must ensure that the locking lever on the microprocessor

socket is in the fully-open position before you insert the microprocessor in the

socket. Failure to do so might result in permanent damage to the

microprocessor, microprocessor socket, and microprocessor-tray assembly.

10.

Install the microprocessor:

Touch the static-protective package containing the new microprocessor to

any

unpainted

metal surface on the server; then, remove the

microprocessor from the package.

Position the microprocessor over the microprocessor connector as shown

in the following illustration. Carefully press the microprocessor into the

socket.

Attention:

To avoid bending the pins on the microprocessor, do not use

excessive force when pressing it into the socket.

Microprocessor

orientation indicator

Microprocessor-

release lever

Microprocessor

connector

Microprocessor

11.

Close the microprocessor-release lever to secure the microprocessor.

Attention:

Do not disturb or contaminate the thermal material on the bottom of the new

heat sink. Doing so damages its heat-conducting capability and exposes the

new microprocessor to overheating.

If you need to remove the heat sink after installing it, note that the thermal

material might have formed a strong bond between the heat sink and the

microprocessor. Do not force the heat sink and microprocessor apart; doing

so can damage the microprocessor pins. Loosening one captive screw fully

before loosening the other captive screw helps break the bond between the

components without damaging them.

12.

Remove the heat sink from its package and remove the cover from the bottom

of the heat sink. Make sure that the thermal material is still on the bottom of

the heat sink. Remove the release liner and orient the heat sink above the

microprocessor; then, press the heat sink into place. Press firmly on the

captive screws and tighten them, alternating between screws until they are

tight. Do not overtighten the screws.

13.

If you installed microprocessor 3 or 4, install the VRM in the associated VRM

socket.

Open the retaining clips at either end of the VRM connector.

Attention:

To avoid breaking the VRM retaining clips or damaging the

VRM connectors, open and close the clips gently.

Chapter 4. Installing options