IBM 88614RX Maintenance Manual - Page 85

press firmly until the blue tabs latch. The backplane assembly will snap into

Get IBM 88614RX - Eserver xSeries 365 PDF manuals and user guides
UPC - 000435172662
View all IBM 88614RX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Release tabs Guide channels 6. Pull out the two blue pushpins. 7. Squeeze the two blue release tabs. 8. Lift the SCSI backplane out of the server slightly; then, disconnect the power cable and remove the backplane. 9. Connect the power cable to the replacement backplane. 10. Slide the backplane into the two guide channels. Note: The cables from steps 4 on page 74 and 5 on page 74 will be routed over the top of the backplane after the backplane is installed. 11. Align the two slots in the backplane assembly onto the two guide tabs; then, press firmly until the blue tabs latch. The backplane assembly will snap into place. 12. Reconnect the cables that were disconnected in step 4 on page 74 and step 5 on page 74. Note: Route cables into the cable channel (in between the fans). Do not allow any cables to catch on any metal protrusions. Chapter 5. FRU information (service only) 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
Release tabs
Guide channels
6.
Pull out the two blue pushpins.
7.
Squeeze the two blue release tabs.
8.
Lift the SCSI backplane out of the server slightly; then, disconnect the power
cable and remove the backplane.
9.
Connect the power cable to the replacement backplane.
10.
Slide the backplane into the two guide channels.
Note:
The cables from steps 4 on page 74 and 5 on page 74 will be routed
over the top of the backplane after the backplane is installed.
11.
Align the two slots in the backplane assembly onto the two guide tabs; then,
press firmly until the blue tabs latch. The backplane assembly will snap into
place.
12.
Reconnect the cables that were disconnected in step 4 on page 74 and step 5
on page 74.
Note:
Route cables into the cable channel (in between the fans). Do not allow
any cables to catch on any metal protrusions.
Chapter 5. FRU information (service only)
75