Intel SC5400RA User Guide - Page 101

Installing and Removing the Intel® Remote Management Module and the Intel® RMM NIC

Get Intel SC5400RA - Server System - 0 MB RAM PDF manuals and user guides
UPC - 675900759336
View all Intel SC5400RA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Installing and Removing the Intel® Remote Management Module and the Intel® RMM NIC Installing the Intel® RMM and the Intel® RMM NIC 1. Observe the safety and ESD precautions in "Safety Information" on page 129. 2. Turn off all peripheral devices connected to the server. Turn off the server. 3. Disconnect the AC power cord from the server. 4. Remove the chassis cover. For instructions, see "Removing the Chassis Cover" on page 24. 5. Open the back panel PCI add-in card retention device by pulling it open from the inside of the system. See letter "B". 6. If a PCI slot cover is installed, remove it by pushing the cover out from the inside of the system. See letter "C". A B AF001527 Figure 85. Preparing System for Addition of Intel® RMM NIC 7. Install the Intel® RMM NIC onto the PCI bracket that came with the kit. See letter "A" in the figure below. 8. Install the PCI bracket into the nearest available PCI slot opening. See letter "B" in the figure below. 9. Attach the RMM NIC cable between the RMM NIC connector on the server board and the connector on the RMM NIC. The server board connector is located between PCI Express slots 3 and 4. See letter "C" in the figure. Intel® Server System SC5400RA User's Guide 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
Intel® Server System SC5400RA User’s Guide
79
Installing and Removing the Intel
®
Remote
Management Module and the Intel
®
RMM NIC
Installing the Intel
®
RMM and the Intel
®
RMM NIC
1.
Observe the safety and ESD precautions in
“Safety Information” on page 129
.
2.
Turn off all peripheral devices connected to the server. Turn off the server.
3.
Disconnect the AC power cord from the server.
4.
Remove the chassis cover. For instructions, see
“Removing the Chassis Cover” on
page 24
.
5.
Open the back panel PCI add-in card retention device by pulling it open from the
inside of the system. See letter “B”.
6.
If a PCI slot cover is installed, remove it by pushing the cover out from the inside of
the system. See letter “C”.
Figure 85. Preparing System for Addition of Intel
®
RMM NIC
7.
Install the Intel
®
RMM NIC onto the PCI bracket that came with the kit. See letter
“A” in the figure below.
8.
Install the PCI bracket into the nearest available PCI slot opening. See letter “B” in
the figure below.
9.
Attach the RMM NIC cable between the RMM NIC connector on the server board
and the connector on the RMM NIC. The server board connector is located between
PCI Express slots 3 and 4. See letter “C” in the figure.
AF001527
A
B