Intel SC5400RA User Guide - Page 125

Remote Management Module and the Intel, RMM NIC if

Get Intel SC5400RA - Server System - 0 MB RAM PDF manuals and user guides
UPC - 675900759336
View all Intel SC5400RA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

7. Reach in through the memory riser cage to disconnect the two power cables from the server board. If necessary, clip the wire tie that holds the two cables together. Use caution so you do not cut any of the cables. 8. Install DIMMs, if necessary. For instructions, see "Installing FBDIMMs" on page 60. 9. Seat the memory risers in the memory cage, pressing down firmly to seat the cards into the server board sockets. 10. Close the door on the memory board cage and tighten the thumscrew to secure the door. 11. Install the Intel® Remote Management Module and the Intel® RMM NIC if necessary. For instructions, see "Installing the Intel® RMM and the Intel® RMM NIC" on page 79. 12. Install any necessary PCI add-in cards. For instructions, see "Installing PCI Add-in Card(s)" on page 54. 13. Connect all remaining power and data cables to the server board. For connection locations, see Figure 8 on page 12. Route the cables as shown in "Power Cable Routing to Fixed Drives" on page 113 and "Data Cable Routing to Fixed Drives" on page 114. 14. Install the processor air duct. For instructions, see "Installing the Processor Air Duct" on page 69. Use caution to make sure you do not pinch any cables. 15. Install the chassis cover. For instructions, see "Installing the Chassis Cover" on page 25. 16. Plug all peripheral devices and the AC power cable into the server. 17. Power up the server. Intel® Server System SC5400RA User's Guide 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
Intel® Server System SC5400RA User’s Guide
103
7.
Reach in through the memory riser cage to disconnect the two power cables from
the server board. If necessary, clip the wire tie that holds the two cables together.
Use caution so you do not cut any of the cables.
8.
Install DIMMs, if necessary. For instructions, see
“Installing FBDIMMs” on
page 60
.
9.
Seat the memory risers in the memory cage, pressing down firmly to seat the cards
into the server board sockets.
10.
Close the door on the memory board cage and tighten the thumscrew to secure the
door.
11.
Install the Intel
®
Remote Management Module and the Intel
®
RMM NIC if
necessary. For instructions, see
“Installing the Intel
®
RMM and the Intel
®
RMM
NIC” on page 79
.
12.
Install any necessary PCI add-in cards. For instructions, see
“Installing PCI Add-in
Card(s)” on page 54
.
13.
Connect all remaining power and data cables to the server board. For connection
locations, see
Figure 8 on page 12
. Route the cables as shown in
“Power Cable
Routing to Fixed Drives” on page 113
and
“Data Cable Routing to Fixed Drives”
on page 114
.
14.
Install the processor air duct. For instructions, see
“Installing the Processor Air
Duct” on page 69
. Use caution to make sure you do not pinch any cables.
15.
Install the chassis cover. For instructions, see
“Installing the Chassis Cover” on
page 25
.
16.
Plug all peripheral devices and the AC power cable into the server.
17.
Power up the server.