Intel SC5400RA User Guide - Page 99

Removing a Heatsink, Installing a Heatsink

Get Intel SC5400RA - Server System - 0 MB RAM PDF manuals and user guides
UPC - 675900759336
View all Intel SC5400RA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

3. Loosely screw in the captive screws on the heat sink corners in the order shown by Figure 84. Do not fully tighten one screw before loosely attaching the others. 4. In the same order, gradually and equally tighten each captive screw until each is firmly tightened. Do not fully tighten one screw at a time. 3 2 1 4 AF001488 Figure 84. Installing a Heatsink 5. Install the processor air duct. For instructions, see "Installing the Processor Air Duct" on page 69. 6. Replace the chassis cover. For instructions, see "Installing the Chassis Cover" on page 25. 7. Reconnect the AC power cord. Removing a Heatsink Caution: • Do not attempt to operate your server system without a heatsink installed over each installed processor. Doing so will cause your server to overheat and may cause permanent damage. • The server system must be operated with both heat sinks installed, regardless of whether one or two processors are installed. Intel® Server System SC5400RA User's Guide 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
Intel® Server System SC5400RA User’s Guide
77
3.
Loosely screw in the captive screws on the heat sink corners in the order shown by
Figure 84. Do not fully tighten one screw before loosely attaching the others.
4.
In the same order, gradually and equally tighten each captive screw until each is
firmly tightened. Do not fully tighten one screw at a time.
Figure 84. Installing a Heatsink
5.
Install the processor air duct. For instructions, see
“Installing the Processor Air
Duct” on page 69
.
6.
Replace the chassis cover. For instructions, see
“Installing the Chassis Cover” on
page 25
.
7.
Reconnect the AC power cord.
Removing a Heatsink
Caution:
•
D
o not attempt to operate your server system without a heatsink installed over each
installed processor. Doing so will cause your server to overheat and may cause
permanent damage.
•
The server system must be operated with both heat sinks installed, regardless of
whether one or two processors are installed.
AF001488
3
1
4
2