Konica Minolta SL1000 Digital Film Scanner SL1000 User Guide - Page 93

Troubleshooting, 2.1 Flashing display of the Indicator Lamp

Get Konica Minolta SL1000 Digital Film Scanner PDF manuals and user guides View all Konica Minolta SL1000 Digital Film Scanner manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Chapter 5 Troubleshooting 2 Troubleshooting 2.1 Flashing display of the Indicator Lamp Indicator Lamp Situation Indicator Lamp in front of the Main Body flashes approximately every second. Action The main body is in the Sleep Condition. It returns normally from the sleep if any key of the application is pressed. Indicator Lamp in front of the Main Body flashes approximately 0.5 cycle of second. The Main Body is in need of service. Please contact an Authorized Dealer for Service. 2.2 Attention display on the Personal Computer Screen Information or Warning message SL-Touch Cannot find the Scanner. Action ・ Confirm the USB Cable Connection is properly connected for the SCAN Mode, start the application after the Scanner Power Switch is turned OFF and ON. ・ Close the Warning Screen for the VIEW Mode, and try the operation again. SL-Touch Error The Scanner is disconnected. The software is switched to the VIEW Mode. ・When using the SCAN Mode, Scanner Power Switch is turned OFF/ON and change to the SCAN Mode. ・ Close the Warning Screen for the VIEW Mode, and try the operation again. SL-Touch "The Scanner is powered OFF for Power Saving, and the software is switched to the VIEW Mode. If you use the Scanner, power ON the Scanner and switch the software to the SCAN Mode. ・When using the SCAN Mode, Scanner Power Switch is turned OFF/ON and change to the SCAN Mode. ・ Close the Warning Screen for the VIEW Mode, and try the operation again. Film Search A target frame was not able to be retrieved. ・ The frame of the Roll Film was not able to be detected. ・ Search the target frame by manually. 5-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Chapter 5 Troubleshooting
5-3
2
Troubleshooting
2.1
Flashing display of the Indicator Lamp
Indicator Lamp Situation
Action
Indicator Lamp in front of the Main Body flashes
approximately every second.
The main body is in the Sleep Condition.
It returns normally from the sleep if any key of the
application is pressed.
Indicator Lamp in front of the Main Body flashes
approximately 0.5 cycle of second.
The Main Body is in need of service.
Please contact an Authorized Dealer for Service.
2.2
Attention display on the Personal Computer Screen
Information or Warning message
Action
SL-Touch
Cannot find the Scanner.
・
Confirm the USB Cable Connection is properly
connected for the SCAN Mode, start the
application after the Scanner Power Switch is
turned OFF and ON.
・
Close the Warning Screen for the VIEW Mode,
and try the operation again.
SL-Touch Error
The Scanner is disconnected.
The software is switched to the VIEW Mode.
・
When using the SCAN Mode, Scanner Power
Switch is turned OFF/ON and change to the SCAN
Mode.
・
Close the Warning Screen for the VIEW Mode,
and try the operation again.
SL-Touch
"The Scanner is powered OFF for Power
Saving, and the software is switched to the
VIEW Mode.
If you use the Scanner, power ON the
Scanner and switch the software to the
SCAN Mode.
・
When using the SCAN Mode, Scanner Power
Switch is turned OFF/ON and change to the SCAN
Mode.
・
Close the Warning Screen for the VIEW Mode,
and try the operation again.
Film Search
A target frame was not able to be retrieved.
・
The frame of the Roll Film was not able to be
detected.
・
Search the target frame by manually.