Home » Netgear Manuals » Hubs & Switches » Netgear M5300-28G3 » Manual Viewer

Netgear M5300-28G3 Web Management User Guide - Page 205

Adv Managed Config Flag

Add to My Manuals
Save this manual to your list of manuals

Page 205 highlights

ProSafe M5300 Switch To configure IPv6 interface information: 1. Use Interface to select the interface to be configured or displayed. All physical interfaces are valid. 2. Use IPv6 Mode to enable/disable IPv6 mode. When IPv6 mode is enabled, interface is capable of IPv6 operation without a global address. In this case, an EUI-64 based link-local address is used. This selector lists the two options for IPv6 mode: enable and disable. Default value is disable. 3. Use DHCPv6 Client Mode to enable or disable the DHCPv6 client mode on an interface. At any point of time only one interface can act as a Client. Default value is disable. 4. Use Stateless Address AutoConfig Mode to enable or disable Stateless Address AutoConfig mode on an interface. Default value is disable. 5. Use Routing Mode to enable/disable routing mode of an interface. Default value is disable. 6. Use Admin Mode to enable/disable the Administrative Mode of the interface. The default value is enable. This mode is not supported for Logical VLAN Interfaces. 7. Use MTU to specify the maximum transmit unit on an interface. If the value is 0 then this interface is not enabled for routing. It is not valid to set this value to 0 if routing is enabled. Range of MTU is 1280 to 1500. 8. Use Duplicate Address Detection Transmits to specify the number of duplicate address detections transmits on an interface. DAD transmits values must be in range 0 to 600. 9. Use Life Time Interval to specify the router advertisement lifetime field sent from the interface. This value must be greater than or equal to the maximum advertisement interval. 0 means do not use the router as the default router. The range of router lifetime is 0 to 9000. 10. Use Adv NS Interval to specify the retransmission time field of router advertisement sent from the interface. A value of 0 means interval is not specified for router. Range of neighbor solicit interval is 1000 to 4294967295. 11. Use Adv Reachable Time to specify the router advertisement time to consider neighbor reachable after ND confirmation. Range of reachable time is 0 to 3600000. 12. Use Adv Interval to specify the maximum time allowed between sending router advertisements from the interface. Default value is 600. Range of maximum advertisement interval is 4 to 1800. 13. Use Adv Managed Config Flag to specify the router advertisement managed address configuration flag. When true, end nodes use DHCPV6. When false, end nodes auto configure addresses. Default value of managed flag is disable. 14. Use Adv Other Config Flag To specify router advertisement for other Stateful configuration flag. Default value of other config flag is disable. 15. Use Adv Suppress Flag to specify router advertisement suppression on an interface. Default value of suppress flag is disable. 16. Use Destination Unreachables to specify the Mode of Sending ICMPv6 Destination Unreachables on this interface. If Disabled then this interface will not send ICMPv6 Destination Unreachables. By default IPv6 Destination Unreachables mode is enable. Field Operational Mode Description Specifies operational state of an interface. Default value is disable. Routing 205

Section	Page
ProSafe M5300 Switch	1
Contents	3
1. Getting Started	9
Switch Management Interface	9
Web Access	9
Understanding the User Interfaces	10
Using the Web Interface	10
Interface Naming Convention	17
2. Configuring System Information	19
Management	19
System Information	20
Switch Statistics	24
System CPU Status	26
Slot Information	27
Loopback Interface	29
Network Interface	30
Time	34
DNS	40
SDM Template Preference	42
License	43
License Key	43
License Features	44
Services	45
DHCP Server	45
DHCP Relay	53
DHCP L2 Relay	54
UDP Relay	57
DHCPv6 Server	59
DHCPv6 Relay	66
Stacking	68
Stack Features	68
Firmware Synchronization and Upgrade	69
Configuration Maintenance	69
Stack Master Election	70
Factory Defaults Reset Behavior	70
Nonstop Forwarding	71
Stack Configuration	72
Stack Port Configuration	74
Stack Port Diagnostics	76
Stack Firmware Synchronization	77
NSF	78
Checkpoint Statistics	80
PoE (M5300-28G-POE+ and M5300-52G-POE+ Only)	82
Basic PoE Configuration	83
PoE Port Configuration	84
SNMP	87
SNMPV1/V2	87
SNMP V3 User Configuration	92
LLDP	93
LLDP	93
LLDP-MED	100
ISDP	109
ISDP Global Configuration	109
Advanced ISDP Configuration	110
Timer Schedule	114
Timer Global Configuration	114
Timer Schedule Configuration	115
3. Configuring Switching Information	119
VLANs	119
Basic	120
Advanced	122
Auto-VoIP Configuration	134
Protocol-Based	134
OUI-Based	136
iSCSI	139
Basic	139
Advanced	141
Spanning Tree Protocol	143
Basic	143
Advanced	145
Multicast	156
MFDB	156
IGMP Snooping	158
MLD Snooping	167
MVR Configuration	173
Basic	173
Advanced	174
Address Table	177
Basic	177
Advanced	179
Ports	181
Port Configuration	181
Port Description	182
Link Aggregation Groups	184
LAG Configuration	184
LAG Membership	186
4. Routing	189
Routing Table	189
Basic	190
Advanced	192
IP	193
Basic	193
Advanced	197
IPv6	201
Basic	201
Advanced	204
VLAN	218
VLAN Routing Wizard	218
VLAN Routing Configuration	219
ARP	220
Basic	221
Advanced	221
RIP	225
Basic	225
Advanced	226
OSPF	232
Basic	232
Advanced	233
OSPFv3	257
Basic	257
Advanced	258
Router Discovery	279
Router Discovery Configuration	279
VRRP	280
Basic	280
Advanced	282
Multicast	286
Mroute Table	287
Multicast Global Configuration	288
Multicast Interface Configuration	289
DVMRP	290
IGMP	296
PIM	304
Static Routes Configuration	311
Admin Boundary Configuration	312
IPv6 Multicast	313
Mroute Table	313
IPv6 PIM	314
MLD	321
Static Routes Configuration	329
5. Configuring Quality of Service	331
Class of Service	331
Basic	332
Advanced	333
Differentiated Services	339
DiffServ Wizard	340
Basic	341
Advanced	343
6. Managing Device Security	355
Management Security Settings	355
Local User	356
Enable Password Configuration	358
Line Password Configuration	358
RADIUS	359
Configuring TACACS+	364
Authentication List Configuration	366
Login Sessions	371
Configuring Management Access	372
HTTP	372
HTTPS	373
SSH	377
Telnet	380
Console Port	381
Denial of Service	382
Access Control	384
Port Authentication	386
Basic	387
Advanced	389
Traffic Control	397
MAC Filter	397
Port Security	399
Private Group	404
Protected Ports Configuration	406
Private VLAN	407
Storm Control	412
Control	414
DHCP Snooping	414
IP Source Guard	419
Dynamic ARP Inspection	421
Captive Portal	426
Configuring Access Control Lists	435
ACL Wizard	435
Basic	437
Advanced	441
7. Monitoring the System	457
Ports	457
Port Statistics	458
Port Detailed Statistics	459
EAP Statistics	466
Cable Test	467
Logs	468
Buffered Logs	469
Command Log Configuration	470
Console Log Configuration	471
SysLog Configuration	471
Trap Logs	472
Event Logs	474
Persistent Logs	476
Port Mirroring	477
Multiple Port Mirroring	477
sFlow	479
Basic	479
Advanced	480
8. Maintenance	483
Save Configuration	483
Save Configuration	483
Auto Install Configuration	484
Reset	485
Device Reboot	485
Factory Default	486
Password Reset	486
Upload File From Switch	487
File Upload	487
HTTP File Upload	488
USB File Upload	489
Download File To Switch	490
File Download	490
HTTP File Download	492
USB File Download	494
File Management	495
Copy	495
Dual Image Configuration	496
Troubleshooting	497
Ping IPv4	497
Ping IPv6	498
Traceroute IPv4	499
Traceroute IPv6	500
9. Help	501
Online Help	501
Support	501
User Guide	502
Registration	503
A. Default Settings	505
B. Configuration Examples	509
Virtual Local Area Networks (VLANs)	509
VLAN Example Configuration	510
Access Control Lists (ACLs)	511
MAC ACL Example Configuration	512
Standard IP ACL Example Configuration	513
Differentiated Services (DiffServ)	514
Class	514
DiffServ Traffic Classes	515
Creating Policies	515
DiffServ Example Configuration	517
802.1X	518
802.1X Example Configuration	520
MSTP	521
MSTP Example Configuration	523
C. Notification of Compliance	525

Match case Limit results 1 per page

Routing

205

ProSafe M5300 Switch

To configure IPv6 interface information:

Use

Interface

to select the interface to be configured or displayed. All physical

interfaces are valid.

Use

IPv6 Mode

to enable/disable IPv6 mode. When IPv6 mode is enabled, interface is

capable of IPv6 operation without a global address. In this case, an EUI-64 based link-local

address is used. This selector lists the two options for IPv6 mode: enable and disable.

Default value is disable.

Use

DHCPv6 Client Mode

to enable or disable the DHCPv6 client mode on an interface. At

any point of time only one interface can act as a Client. Default value is disable.

Use

Stateless Address AutoConfig Mode

to enable or disable Stateless Address

AutoConfig mode on an interface. Default value is disable.

Use

Routing Mode

to enable/disable routing mode of an interface. Default value is disable.

Use

Admin Mode

to enable/disable the Administrative Mode of the interface. The default

value is enable. This mode is not supported for Logical VLAN Interfaces.

Use

MTU

to specify the maximum transmit unit on an interface. If the value is 0 then this

interface is not enabled for routing. It is not valid to set this value to 0 if routing is enabled.

Range of MTU is 1280 to 1500.

Use

Duplicate Address Detection Transmits

to specify the number of duplicate address

detections transmits on an interface. DAD transmits values must be in range 0 to 600.

Use

Life Time Interval

to specify the router advertisement lifetime field sent from the

interface. This value must be greater than or equal to the maximum advertisement interval.

0 means do not use the router as the default router. The range of router lifetime is 0 to 9000.

10.

Use

Adv NS Interval

to specify the retransmission time field of router advertisement sent

from the interface. A value of 0 means interval is not specified for router. Range of neighbor

solicit interval is 1000 to 4294967295.

11.

Use

Adv Reachable Time

to specify the router advertisement time to consider neighbor

reachable after ND confirmation. Range of reachable time is 0 to 3600000.

12.

Use

Adv Interval

to specify the maximum time allowed between sending router

advertisements from the interface. Default value is 600. Range of maximum advertisement

interval is 4 to 1800.

13.

Use

Adv Managed Config Flag

to specify the router advertisement managed address

configuration flag. When true, end nodes use DHCPV6. When false, end nodes auto

configure addresses. Default value of managed flag is disable.

14.

Use

Adv Other Config Flag

To specify router advertisement for

other

Stateful configuration

flag. Default value of other config flag is disable.

15.

Use

Adv Suppress Flag

to specify router advertisement suppression on an interface.

Default value of suppress flag is disable.

16.

Use

Destination Unreachables

to specify the Mode of Sending ICMPv6 Destination

Unreachables on this interface. If Disabled then this interface will not send ICMPv6

Destination Unreachables. By default IPv6 Destination Unreachables mode is enable.

Field

Description

Operational Mode

Specifies operational state of an interface. Default value is disable.