Panasonic AJHD1400 AJHD1400 User Guide - Page 36
SYSTEM, No./Item, Description of setting, ENCODER, LOCAL, <Notes>, V LEVEL, SYS H, SYS SC
View all Panasonic AJHD1400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 36 highlights
Setup menus (continued) SYSTEM No./Item Description of setting 05 ENCODER SEL 06 V LEVEL CTRL 12 SYS H (HD) 14 SYS SC (SD) For setting whether to perform the various adjustments for the video output signals using this VTR or using an external encoder remote controller. 0001 LOCAL : The various adjustments for the video output signals are performed using this VTR. 0002 BOTH : The various adjustments for the video output signals are performed using both this VTR and an external encoder remote controller. z For video adjustments, refer to "Video output signal adjustments" (page 35). z If the signals are adjusted with the external encoder remote controller, the adjusted values are reflected in the setup menu. However, the adjusted numerical values will not be stored unless about 1 minute has elapsed after completion of the adjustment operation. If the unit is turned off after executing the adjustments with the external encoder remote controller, it is necessary to wait about 1 minute before turning off the power. z Settings in this menu are not effective for the IEEE1394 digital output. For selecting what is to be controlled when the video output level is to be adjusted by an external encoder remote controller. 0000 HD : The HD video output level can be adjusted. 0001 SD : The SD video output level can be adjusted. 0002 BOTH : Both the HD and SD video output levels can be adjusted. When "CMPST" is selected in menu No. 650 STYLE, the unit will be in the same state as when "BOTH" is selected, regardless of the settings in this item. For adjusting the system phase of the HD SDI output signals. (in 13.5 ns increments). - :Phase advances. + :Phase delays. 0000 -1100 : : 1100 0 : : 2200 1100 z When menu item No. 25 SYSTEM FREQ is set to 50i/25P, 25 (HD), 25(SD), 50 (HD) or 50 (SD), the setting range is from -1320 - 0 - 1320. z When menu item No. 25 SYSTEM FREQ is set to 23/24, the setting range is from -1375 - 0 - 1375. For adjusting the system phase of the analog composite output and SD SDI output signals (total variable range of over ±180 degrees). - :Phase advances. + :Phase delays. 0000 -108 : : 0108 0 : : 0216 108 No./Item Description of setting 15 VO SYS H (SD) 16 SD SYS H (SD) For adjusting the system phase of the analog composite output signals (in 37 ns increments). - :Phase advances. + :Phase delays. 0000 -858 : : 0858 0 : : 1716 858 The setting range is -864 to 0 to 864 when 50i/25P, 25 (HD) or 25 (SD) is selected as the menu item No.25 SYSTEM FREQ setting. For adjusting the system phase of the SD SDI output signals (in 37 ns increments). - :Phase advances. + :Phase delays. 0000 -858 : : 0858 0 : : 1716 858 The setting range is -864 to 0 to 864 when 50i/25P, 25 (HD) or 25 (SD) is selected as the menu item No.25 SYSTEM FREQ setting. 18 SCH COAR (SD) For adjusting the SCH (sub-carrier to horizontal) phase of the analog composite output signals (4 positions in 90-degree increments). The SC phase changes, and the H phase remains unchanged. 0000 0 0001 90 0002 180 0003 270 19 SCH FINE (SD) For adjusting the SCH (sub-carrier to horizontal) phase of the analog composite output signals (variable range of over ±45 degrees). The SC phase changes, and the H phase remains unchanged. A range of ±180 degrees is covered by using this setting in combination with item No.18 SCH COAR (SD). 0000 -32 : : 0032 0 : : 0064 32 20 AV PHASE For adjusting the phase of the AUDIO output signals in relation to the video output signals (in 20.8 µs increments). - :Audio phase against image advance. + :Audio phase against image delay. 0000 -100 : : 0100 0 : : 0200 100 "_____" indicates the factory setting. 36