Panasonic AJHD1400 AJHD1400 User Guide - Page 46

Setup menus (continued) TIME CODE (continued) No./Item Description of setting 506*1 REGEN MODE 507*1 EXT TC SEL 508*1 BINARY GP 509 PHASE CORR 510*1 TCG CF FLAG For selecting the editing mode range when the VTR is operating in the REGEN mode while performing editing operations with "AUTO" selected as the menu item No.503 TCG MODE setting. 0000 AS&IN : Regeneration applies during assemble or insert editing. 0001 ASSEM : Regeneration applies during assemble editing. 0002 INSRT : Regeneration applies during insert editing. At the time of frame-by-frame shooting, the operations are equivalent to assemble editing. For selecting the time code to be used when an external time code is used. 0000 EXT_L : The LTC information of the TIME CODE IN connector is used. 0001 SLTC : The LTC information added to the serial signals which are supplied to the HD SDI IN connector is used. 0002 SVITC : The VITC information added to the serial signals which are supplied to the HD SDI IN connector is used. When selecting "1394" with the INPUT VIDEO switch on the front panel, the time code input to IEEE1394 digital input/output connector is used. The VITC information will not be superimposed onto the video signal output when recording is performed or the EE mode is established. The LTC information and VITC information are not superimposed onto the HD serial output signals. For setting the usage status for the user bits of the time code generated by the TCG. 0000 000 : No character set specified 0001 001 : 8-bit character set complying with the ISO646 and ISO2022 standards 0002 010 : Undefined 0003 011 : Undefined 0004 100 : Undefined 0005 101 : Page/line 0006 110 : Undefined 0007 111 : Undefined For setting whether to control the phase correction of the LTC output during playback. 0000 OFF : The phase correction is not controlled. 0001 ON : The phase correction is controlled. For selecting whether to set the CF flag of the TCG to ON. 0000 OFF : The CF flag is set to OFF. 0001 ON : The CF flag is set to ON. No./Item Description of setting 511*1 DF MODE For selecting whether to use the DF or NDF mode for CTL and TCG. 0000 DF : The drop frame (DF) mode is used. 0001 NDF : The non-drop frame (NDF) mode is used. 512*1 TC OUT REF When the TCG switch of the front panel is set to EXT, it switches the phase of time code output from the TC OUT connector for external LTC input. (In EE mode only) 0000 VOUT : Match the output image. 0001 TC_IN : Match the external time code input. 513 VITC OUT For selecting how to output the VITC signal which is superimposed onto the output video signal. 0000 SBC : In the playback mode, the time code recorded in the SBC area*A is output. 0001 VAUX : In the playback mode, the time code recorded in the VAUX area*B is output. z The VITC information which is detected by the HD serial input is automatically recorded in the VAUX area when the images are recorded. z When "23/24," "25(HD)," "25(SD)," "50(HD)" or "50(SD)" is selected as the menu item No.25 SYSTEM FREQ setting and VAUX is selected as the VITC OUT setting, the time code which is output may not be continuous. 514*1 HD EMBD VITC For selecting whether to superimpose the VITC information onto the HD serial output. 0000 OFF : The VITC information is not superimposed. 0001 ON : The VITC information is superimposed. 515*1 HD EMBD LTC For selecting whether to superimpose the LTC information onto the HD serial output. 0000 OFF : The LTC information is not superimposed. 0001 ON : The LTC information is superimposed. *1 Displayed menus may vary depending on the settings in menu No. 25 SYSTEM FREQ. For details, refer to "Menus which are displayed" (page 32). *A The SBC (Sub Code Data) area is an area that exists separately from the video and audio area on the helical track and contains the tape management information, such as the time code, in compliance with the SMPTE/ EBU and the recording time. As with the ordinary LTC (Linear Time Code), the time code can be read even when rewinding/fast-forwarding and can be read out when the tape stops. *B The VAUX (Video Auxiliary Data) area is an area in the video area on the helical track and contains information related to the video data. "_____" indicates the factory setting. 46