Panasonic AJHD1400 AJHD1400 User Guide - Page 45

Setup menus (continued) TAPE PROTECT No./Item Description of setting 400 For setting the time to be taken before the unit is set STILL TIMER in the tape protection mode when it is left standing in the STOP or STILL status. (Units: S = seconds, min = minutes) 0000 0.5S 0001 5S 0002 10S 0003 20S 0004 30S 0005 40S 0006 50S 0007 1min 0008 2min When a DV, DVCAM or an unused tape is used, or a DVCPRO HD/DVCPRO50/DVCPRO tape is used in the EE mode, any setting above 2 (10S) will result in a setting time of 10 seconds. 401 SRC PROTECT For setting the operation to be performed in the tape protection mode when the unit is left standing in the STILL status (JOG/VAR/SHTL). 0000 STEP : STEP FWD 0001 HALF : STANDBY OFF (HALF LOADING) When STEP FWD is selected, the unit is automatically transferred to the standby OFF (half loading) mode when the unit is left standing in the STOP mode for a total of 30 minutes (or 1 minute for DV or DVCAM tape). 402 DRUM STDBY For setting the cylinder operation in the standby OFF (half loading) mode. 0000 OFF The cylinder stops rotating. 0001 ON The cylinder continues to rotate. 403 STOP PROTECT For setting the operation to be performed in the tape protection mode when the unit is left standing in the STOP status. 0000 STEP : STEP FWD 0001 HALF : STANDBY OFF (HALF LOADING) When STEP FWD is selected, the unit is automatically transferred to the standby OFF (half loading) mode when the unit is left standing in the STOP mode for a total of 30 minutes (or 1 minute for DV or DVCAM tape). "_____" indicates the factory setting. TIME CODE No./Item Description of setting 500*1 VITC BLANK For setting whether to output the VITC signal at the position which is set using menu items No.501 VITC POS-1 and No.502 VITC POS-2. 0000 BLANK : The VITC signal is not output. 0001 THRU : The VITC signal is output. This setting takes effect only with the SD output (analog composite output and SD SDI output). 501*1*2 VITC POS-1 For setting the position where the VITC signal is to be inserted. 0000 10L 0000 7L : : : : 0006 16L 0004 11L : : : : 0010 20L 0015 22L z The same line as the one selected by menu item No.502 VITC POS-2 and No.692 UMID POS cannot be selected. z This setting takes effect only with the SD output (analog composite output and SD SDI output). 502*1*2 VITC POS-2 For setting the position where the VITC signal is to be inserted. 0000 10L 0000 7L : : : : 0008 18L 0008 13L : : : : 0010 20L 0015 22L z The same line as the one selected by menu item No.501 VITC POS-1 and No.692 UMID POS cannot be selected. z This setting takes effect only with the SD output (analog composite output and SD SDI output). 503*1 TCG MODE For setting the synchronization of the internal time code generator. 0000 SW : When the TCG switch on the front panel is set to REGEN or PRESET, the selection is complied. 0001 AUTO : REGEN or PRE is automatically selected depending on the operation mode. When editing (including a chained shot): REGEN is selected. Other than the above: PRE is selected. 504*1 RUN MODE For setting the operation mode in which the internal time code generator runs. 0000 REC : The generator runs only while recording is in progress. 0001 FREE : The generator runs while the power is on regardless of the unit's operation mode. 505*1 TCG REGEN For setting the signal to be regenerated when the TCG (time code generator) is in the regeneration mode. 0000 TC&UB : Both the time code and user bits are regenerated. 0001 TC : Only the time code is regenerated. 0002 UB : Only the user bits is regenerated. *1 Displayed menus may vary depending on the settings in menu No. 25 SYSTEM FREQ. For details, refer to "Menus which are displayed" (page 32). *2 Even if the RESET button is pressed while pressing the SEARCH button, the value may not return to the factory setting. 45