Panasonic AJHD1400 AJHD1400 User Guide - Page 61
Displaying the warning information, Warning messages
View all Panasonic AJHD1400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 61 highlights
Error messages (continued) Displaying the warning information z A warning message appears when a warning has occurred. "NO WARNING" appears when a warning has not occurred. z When more than one warning has occurred simultaneously, move the joystick up or down to check the description of each warning. Warning messages Priority Monitor display Description Corrective action VTR operation High E-20 (DEW) E-95 (INVALID EMBEDDED TC) E-92 (1394 INITIAL ERROR) E-04 (UNKNOWN SIG) If condensation is detected, the error number flashes and the unit transfers to eject mode. The drum rotates after the cassette is ejected to eliminate the condensation. Once the unit is released from condensation status, the error message display is cleared and the VTR is able to be used. Leave the power on and wait. z If condensation is detected in the eject mode, the drum starts rotating as soon as it is detected. z If condensation is detected when the cassette has been inserted, the drum rotation is stopped, and after the tape is ejected, the drum starts rotating. EJECT (When "SLTC" is selected in menu No. 032 REC REF) Appear when a time code for a signal input into the HD SDI IN connector is not stepping at the standard rate in synchronizing the image frames to be recorded with the time code. Check the time code Operation information of the input signal. continues. If the cable connection is in loop status, reconnect to 1 to Display if the IEEE1394 digital interface connection status 1. is irregular If not using the loop connection, turn the POWER switch OFF > ON. Signal input and output through the IEEE1394 digital interface is stopped. This appears when the signals supplied from the IEEE1394 digital interface are not DVCPRO/DV format signals. Check that the 1394 input has been connected properly. No recording o perations are possible. E-90 This appears when the initialization process fails during (NOT 1X 100M SIG) communication via the IEEE1394 digital interface. Check the input signal. Operation continues.*1 E-16 (INVALID VIDEO SIG) E-17 (INVALID AUDIO SIG) E-18 (INVALID TC SIG) E-14 (NO MATCH SIG) E-10 (FAN STOP) E-09 (NO RF) This appears when the compressed video signals supplied from the IEEE1394 digital interface are irregular Check the 1394 input signals.It signals. is possible that playback Operation z This warning appears only during recording operations. signals of an unrecorded tape continues.*1 In such cases, no signals are recorded on the tape, are being input. and only erasure of existing signals is performed. This appears when the audio signals supplied from the Check the 1394 input signals.It IEEE1394 digital interface are irregular signals. is possible that signals other z This warning appears only during recording operations. than 1x playback signals are In such cases, the signals are recorded with the audio being input from a VTR or Operation continues.*2 signals muted. other device. This appears when the time code information supplied from the IEEE1394 digital interface is irregular information. z This warning appears only during recording operations. In such cases, the internally generated time code is Check the time code of the device which is supplying the time code. recorded. Operation continues.*3 This appears when the signals supplied to the IEEE1394 digital interface are at variance from the system format Check the input signal. which is set by this unit. Operation continues.*1 This appears when the fan motor has shut down. z The power automatically turns off if 5 minutes pass with the fan stopped. Check the fan for foreign matter. Operation continues. This appears when a blank section lasting for more than one second on the tape has been detected during playback. A blank section is identified as such when all the following conditions are met: z There are no output signals from any of the heads. Check the tape. It is possible that an unrecorded tape has been loaded. z The playback data cannot be read. z There is no CTL signal (DV/DVCAM tapes excluded). Operation continues. *1 This error message always appears in the EE mode. In such a case, black signals are recorded as the video signals, and the audio signals are muted. *2: This error message always appears in the EE mode. In such a case, the audio signals are muted. *3: This error message always appears in the EE mode. In such a case, the time code of the time code generator inside this unit is recorded as the time code signal. 61