Home » Panasonic Manuals » Audio Mixers » Panasonic AV-HS410 » Manual Viewer

Panasonic AV-HS410 Operating Instructions Advanced - Page 133

Output, Select, SDI Limit, Output SDI, Assign, Source, Converter, Scale, Delay, Sharp, Analog

Add to My Manuals
Save this manual to your list of manuals

Page 133 highlights

5. Setting menu table Menu Output Sub menu Use [F1] to select. Output Parameter Setting range Output (SDI) / Y Assign SDI OUT1 to SDI OUT5, OUT A1, OUT A2, OUT B1 or OUT B2 is displayed in the Y part. (OUT A1, OUT A2, OUT B1 and OUT B2 take effect when the AV-HS04M7 board has been connected.) Default value Parameter Setting range Default value Down Converter Parameter (Enabled when Setting range the AV-HS04M7 option board has been connected.) Default value Output (Analog) / Y Assign Parameter OUT A1, OUT A2, OUT B1 or OUT B2 is displayed in the Y part. (OUT A1, OUT A2, OUT B1 and OUT B2 take effect when the AV-HS04M4 board has been connected. OUT A2 and OUT B2 take effect when the AV-HS04M5 board has been connected.) Setting range Default value Parameter 1 Parameter 2 Parameter 3 Parameter 4 Use [F2] to select. Use [F3] to select. Use [F4] to select. Use [F5] to select. Select () SDI Limit SDI OUT1 to 5, DVI OUT, OUT-A1, OUT-A2, OUT-B1, OUT-B2 Off, 108, 104, 100 SDI OUT1 Off Source Mode PGM, PVW, Normal, CLN, AUX1 to 4, Down Convert MV, KeyOut, ("Down Convert" MEM-PVW takes effect when AV-HS04M7 is connected.) PGM(OUT1), Normal PVW(OUT2), AUX1(OUT3), AUX2(OUT4), AUX3(OUT5), AUX1(OUTA1), AUX2(OUTA2), AUX3(OUTB1), AUX4(OUTB2) Scale Delay Sharp Squeeze, Edge Crop, Letter Box 90H(75H), 1F Squeeze 90H(75H) Source PGM, PVW, CLN, AUX1 to 4, MV, Key Out, MEM-PVW 1 to 5 3 AUX1(OUTA1), AUX2(OUTA2), AUX3(OUTB1), AUX4(OUTB2) 133

Section	Page
Contents	3
Before use	5
Overview	5
Concerning the ratings display	5
Disclaimer of warranty	5
Network security	5
Concerning differences in the system versions	6
1. Basic operations	7
1-1. Background transition	7
1-1-1. Selecting the bus	7
1-1-2. Selecting the bus using the SHIFT function	7
1-1-3. Selecting the bus mode	8
1-1-4. Selecting the transition mode	8
1-1-5. Manual transition	9
1-1-6. Auto transition	9
1-1-7. Cut transition	9
1-2. Wipe	10
1-2-1. Selecting the wipe pattern	10
1-2-2. Selecting the wipe direction	11
1-2-3. Wipe decorations (border, soft effect)	11
1-2-4. Setting the wipe start position	12
1-2-5. Modifying wipe	12
1-2-6. Setting the latency	14
1-3. Key	15
1-3-1. Selecting the key type	15
1-3-2. Selecting the key material	16
1-3-3. Key transitions	17
1-3-4. Key preview	19
1-3-5. Adjusting the luminance key and linear key	19
1-3-6. Adjusting the chroma key	20
1-3-7. Key decorations	26
1-3-8. Masking the key signals	27
1-3-9. Flying key	28
1-3-10. Setting the priority	28
1-4. PinP (picture in picture)	29
1-4-1. Selecting the PinP channel and material	29
1-4-2. Transition between PinP materials	29
1-4-3. Selecting Shape	30
1-4-4. PinP preview	30
1-4-5. PinP transitions	30
1-4-6. PinP adjustments	31
1-4-7. Linking PinP1 and PinP2	32
1-4-8. PinP decorations	33
1-4-9. Trimming settings	34
1-5. DSK (downstream key)	35
1-5-1. Selecting the DSK type	35
1-5-2. Selecting the DSK material	36
1-5-3. DSK transitions	36
1-5-4. DSK preview	37
1-5-5. DSK adjustments	37
1-5-6. DSK decorations	38
1-5-7. Masking the DSK signals	39
1-6. Key Link	40
1-7. FTB (Fade to Black)	41
1-8. Internal color signals	42
1-8-1. Setting the color background	42
1-8-2. Setting the Wash effect	42
1-9. Switching the AUX output	44
1-9-1. Selecting the AUX output materials	44
1-9-2. AUX1 transitions	44
1-9-3. Setting enable/disable for the AUX1 transition	45
1-10. Memory	46
1-10-1. Memory registration and recall items	47
1-10-2. Storing the settings in the memory (Store)	47
1-10-3. Recalling the operations stored in the memory (Recall)	48
1-10-4. Memory preview	49
1-10-5. Deleting the operations stored in the memory (Delete)	50
1-10-6. Selecting the buses whose settings are to be registered and or played back	51
1-10-7. Registering the material selection items	52
1-10-8. Setting effect dissolve (shot memory)	52
1-10-9. Editing event memory timelines	53
1-10-10. Registering memories (Register)	59
1-11. Video memories	60
1-11-1. Recording still images (Still)	61
1-11-2. Recording moving images (Clip)	62
1-11-3. Saving Images in Flash Memory	63
1-11-4. Playing back moving images (Clip)	64
1-12. Memory card	67
1-12-1. Initializing the memory cards	69
1-12-2. Saving data on memory cards	69
1-12-3. Loading data from memory cards	70
1-12-4. Deleting files on memory cards	71
1-12-5. Displaying the memory card information	71
1-13. Waveform monitor settings	72
1-14. Setting the status display	73
2. Input/output signal settings	74
2-1. Input signal settings	74
2-1-1. Setting the frame synchronizer	76
2-1-2. Setting the input mode	77
2-1-3. Setting the delay amount	78
2-1-4. Freezing the input signals	78
2-1-5. Setting the material names	78
2-1-6. Setting the up-converter	79
2-1-7. Setting the video process function	80
2-1-8. Setting the analog input gain (option)	80
2-1-9. Setting the analog composite input signals (option)	81
2-1-10. Setting the DVI input signals	82
2-1-11. Displaying the DVI input signal information	86
2-1-12. Adjusting the DVI input signals	87
2-1-13. Automatic adjustment of the black level and white level (analog input signals)	87
2-2. Output signal settings	88
2-2-1. Assigning the output signals	89
2-2-2. Setting the SDI output color range	89
2-2-3. Setting the DVI output signals	90
2-2-4. Setting the down-converter (option)	92
2-3. Setting the sync signals	93
2-4. Adjusting the output signal phase	93
2-5. Setting the multi view display	97
2-5-1. Setting the screen layout	97
2-5-2. Setting the split frame and characters	98
2-5-3. Setting the tally displays	98
2-5-4. Changing the material names	99
2-5-5. Setting the level meters	100
2-5-6. Setting the input signal marks	100
2-5-7. Setting the markers	100
2-5-8. High-resolution multi view mode	100
2-6. Setting the ancillary data and embedded audio data	101
3. System settings	102
3-1. Setting the system format	102
3-2. Setting the crosspoints	103
3-2-1. Assigning signals to the crosspoints	103
3-2-2. Setting the crosspoint switching	104
3-3. Button assignments	105
3-3-1. Setting the user buttons	105
3-4. Setting the date and time	106
3-5. Network settings	106
3-6. Setting the built-in display backlight and button illumination	107
3-7. Status displays	108
3-7-1. Alarm status displays	108
3-7-2. Alarm message	108
3-7-3. Displaying the version information and option information	109
3-8. Initialization	110
3-8-1. Initializing setting data	110
3-8-2. Initializing fader	110
4. External interfaces	111
4-1. Setting the GPI I/O	111
4-2. LAN	115
4-3. EDITOR	115
4-4. COM	115
4-5. Plug-in software	116
5. Setting menu table	117
Appendix (glossary)	139

Match case Limit results 1 per page

133

Sub menu

Parameter 1

Parameter 2

Parameter 3

Parameter 4

Use [F1] to select.

Use [F2] to select. Use [F3] to select. Use [F4] to select. Use [F5] to select.

Output

Parameter

Select (



)

SDI Limit

Setting range

SDI OUT1

DVI OUT,

OUT-A1,

OUT-A2,

OUT-B1,

OUT-B2

Off, 108, 104,

100

Default value

SDI OUT1

Off

Output (SDI)

/ Y

SDI OUT1 to SDI OUT5,

OUT A1, OUT A2,

OUT B1 or OUT B2 is

displayed in the Y part.

(OUT A1, OUT A2,

OUT B1 and OUT B2

take effect when the

AV-HS04M7 board has

been connected.)

Assign

Parameter

Source

Mode

Setting range

PGM, PVW,

CLN, AUX1

MV, KeyOut,

MEM-PVW

Normal,

Down Convert

(“Down Convert”

takes effect when

AV-HS04M7 is

connected.)

Default value

PGM(OUT1),

PVW(OUT2),

AUX1(OUT3),

AUX2(OUT4),

AUX3(OUT5),

AUX1(OUTA1),

AUX2(OUTA2),

AUX3(OUTB1),

AUX4(OUTB2)

Normal

Down

Converter

Parameter

Scale

Delay

Sharp

(Enabled when

the AV-HS04M7

option board has

been connected.)

Setting range

Squeeze,

Edge Crop,

Letter Box

90H(75H), 1F

Default value

Squeeze

90H(75H)

Output (

Analog

) / Y

OUT A1, OUT A2,

OUT B1 or OUT B2 is

displayed in the Y part.

(OUT A1, OUT A2,

OUT B1 and OUT B2

take effect when the

AV-HS04M4 board has

been connected.

OUT A2 and OUT B2

take effect when the

AV-HS04M5 board has

been connected.)

Assign

Parameter

Source

Setting range

PGM, PVW,

CLN, AUX1

MV, Key Out,

MEM-PVW

Default value

AUX1(OUTA1),

AUX2(OUTA2),

AUX3(OUTB1),

AUX4(OUTB2)

5. Setting menu table