Panasonic WJHD200 WJHD200 User Guide - Page 35

Alarm Setup, Alarm Buzzer ALARM BUZZ, Video Loss VIDEO LOSS, Monitor Mode MONITOR MODE

Get Panasonic WJHD200 - Digital Disk Recorder PDF manuals and user guides View all Panasonic WJHD200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

I Alarm Setup (ALARM SETUP) The digital disk recorder accepts alarm signals supplied from connected devices such as sensors or camera site equipment. The recorder itself also generates an alarm signal when the preset motion detection is activated. Any alarm signal starts recording with the preset recording mode, field rate, and picture quality specified in the REC MODE menu described earlier. Alarm recording stops when the preset time has elapsed, the alarm [RESET] button on the front panel is pressed, or the ALARM RESET IN signal is supplied from the connected device. The recorder outputs an alarm recovery signal from the rear panel. ALARM SETUP ALARM BUZZ ON VIDEO LOSS ON MONITOR MODE SPOT VMD SETUPO G Alarm Buzzer (ALARM BUZZ) Enables or disables buzzer beeping when an alarm operates. 1. Move the cursor to ALARM BUZZ with the [D] or [C] button. 2. Rotate the JogDial to select ON or OFF. The default is ON. ON: Buzzer beeps while alarm is active. OFF: Buzzer does not beep. G Video Loss (VIDEO LOSS) Enables or disables video loss detection. 1. Move the cursor to VIDEO LOSS with the [D] or [C] button. 2. Rotate the JogDial to select ON or OFF. The default is ON. ON: Enables the recorder to detect video loss. OFF: Ignores video loss. 1. Move the cursor to MONITOR MODE with the [D] or [C] button. 2. Select the parameter with the JogDial, and press the JogDial. The default is SPOT. SPOT: Switches to the picture of the alarmed channel. OFF: Retains the previous display mode. G Video Motion Detection (VMD SETUP) A VMD or Video Motion Detector senses changes in the video signals within a preset area and supplies alarm output. When a change is detected, the recorder starts recording. The detection sensitivity and area are selected on this menu. 1. Move the cursor to VMD SETUPO with the [D] or [C] button, and press the JogDial. The VMD SETUP window opens. CAM 1 2 3 4 5 6 7 8 VMD SETUP SENS OFF LOWO MIDO HIGHO OFF OFF OFF OFF 2. Move the cursor to the desired line. 3. Rotate the JogDial to select the desired parameter, and press the JogDial. The default is OFF. LOW: Low sensitivity MID: Medium sensitivity HIGH: High sensitivity OFF: Motion detection is disabled. The area setup window appears with an asterisk when other than OFF is selected. The asterisk represents the upper-left or bottom-right of the detection area. The division lines are not actually displayed on the monitor. G Monitor Mode (MONITOR MODE) This setting specifies whether to allow the display to change from the currently displayed picture to the alarmed channel when an alarm operates. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
35
■
Alarm Setup (ALARM SETUP)
The digital disk recorder accepts alarm signals supplied
from connected devices such as sensors or camera site
equipment. The recorder itself also generates an alarm sig-
nal when the preset motion detection is activated. Any
alarm signal starts recording with the preset recording
mode, field rate, and picture quality specified in the REC
MODE menu described earlier. Alarm recording stops
when the preset time has elapsed, the alarm [RESET] but-
ton on the front panel is pressed, or the ALARM RESET IN
signal is supplied from the connected device. The recorder
outputs an alarm recovery signal from the rear panel.
●
Alarm Buzzer (ALARM BUZZ)
Enables or disables buzzer beeping when an alarm oper-
ates.
1. Move the cursor to ALARM BUZZ with the [
D
] or [
C
]
button.
2.
Rotate the JogDial to select ON or OFF.
The default is ON.
ON:
Buzzer beeps while alarm is active.
OFF:
Buzzer does not beep.
●
Video Loss (VIDEO LOSS)
Enables or disables video loss detection.
1. Move the cursor to VIDEO LOSS with the [
D
] or [
C
]
button.
2.
Rotate the JogDial to select ON or OFF.
The default is ON.
ON:
Enables the recorder to detect video loss.
OFF:
Ignores video loss.
●
Monitor Mode (MONITOR MODE)
This setting specifies whether to allow the display to
change from the currently displayed picture to the alarmed
channel when an alarm operates.
1. Move the cursor to MONITOR MODE with the [
D
] or
[
C
] button.
2. Select the parameter with the JogDial, and press the
JogDial.
The default is SPOT.
SPOT:
Switches to the picture of the alarmed channel.
OFF:
Retains the previous display mode.
●
Video Motion Detection
(VMD SETUP)
A VMD or Video Motion Detector senses changes in the
video signals within a preset area and supplies alarm out-
put. When a change is detected, the recorder starts record-
ing. The detection sensitivity and area are selected on this
menu.
1. Move the cursor to VMD SETUP
O
with the [
D
] or [
C
]
button, and press the JogDial. The VMD SETUP window
opens.
2.
Move the cursor to the desired line.
3.
Rotate the JogDial to select the desired parameter, and
press the JogDial.
The default is OFF.
LOW:
Low sensitivity
MID:
Medium sensitivity
HIGH:
High sensitivity
OFF:
Motion detection is disabled.
The area setup window appears with an asterisk when
other than OFF is selected. The asterisk represents the
upper-left or bottom-right of the detection area. The
division lines are not actually displayed on the monitor.
ALARM SETUP
ALARM BUZZ
ON
VIDEO LOSS
ON
MONITOR MODE
SPOT
VMD SETUP
O
VMD SETUP
CAM
SENS
1
OFF
2
LOW
O
3
MID
O
4
HIGH
O
5
OFF
6
OFF
7
OFF
8
OFF