Pioneer VSX-45TX Owner's Manual - Page 65

Remote Control of Other Components SETUP 6-7, 9,10 S0URCE TV SYSTEM RECEIVER OFF DVD/LD TV/SAT VCR1/ DVR MULTI CONTROL VCR2 VIDEO CD TV CONT MULTI OPERATION CD-R/ TAPE1 MD/ TAPE2 TUNER RECEIVER DIMMER LOUDNESS 1 2 TONE EFFECT/CH SEL 3 4 SIGNAL SEL 5 VIDEO SEL 9 DNR BASS/TREBLE + 6 7 8 HI-BIT +10 - DISC 0 ENTER SYSTEM SETUP DIRECT ACCESS SEARCH MODE GUIDE MENU TOP MENU TUNER EDIT ENTER TRACK EXIT AUDIO RETURN MPX ¶ TUNING - 1 STATION - 4 CHANNEL - DTV ON/OFF 8 BAND 3 DTV MENU CLASS 7 DISP MODE SUB TITLE TUNING + ¡ STATION + ¢ CHANNEL+ TV INPUT TV CONTROL TV VOL TV CH INPUT MIDNIGHT MULTI CH INPUT VOLUME MOVIE MUSIC ACOUSTIC EQ MODE SURROUND STEREO/ DIRECT ENTER SB CH MODE MUTE REMOTE SETUP Î Buttons that are able to learn new commands AV PRE-PROGRAMMED AND LEARNING REMOTE CONTROL UNIT AXD7290 MUTE LIGHT Î LISTENING CH SELECT (DVD-A/SACD) MULTI CH INPUT ACOUSTIC CAL STEREO /DIRECT LISTENING MODE ADVANCED CONCERT ADVANCED CINEMA SURROUND STANDARD THX VOLUME INPUT MIDNIGHT DIGITAL NR TV INPUT TV CONTROL TV VOL TV CH EXTRA MENU TUNING + ¡ STATION + ¢ CHANNEL+ DTV ON/OFF 8 BAND 3 DTV MENU CLASS 7 MPX ¶ TUNING - 1 STATION - 4 CHANNEL - RETURN GUIDE EXIT STATUS ENTER TUNER EDIT MENU DIRECT ACCESS DISP MODE REMOTE SETUP SYSTEM SETUP - +10 + DISC ENTER 0 9 TONE BASS/TREBLE 8 7 6 5 VIDEO SEL SIGNAL SEL TAPE 2 EFFECT/CH SELL 4 3 2 1 DIMMER INPUT ATT LOUDNESS SPEAKER A/B TUNER RECEIVER CD-R/ TAPE1 CD TV CONT MULTI OPERATION VCR2 VIDEO VCR1/ DVR MULTI CONTROL SAT TV DVD/LD S0URCE TV SYSTEM RECEIVER OFF SETUP 5 While LEARN continues to flash, point the two remote controls toward each other. Press the button on the other remote control corresponding to the operation you want to program. 2-8 inches After the process is complete and the command has been learned, OK will appear in the remote control display. If NG (no good) appears, it means that for some reason the command was not learned. In this case, repeat steps 4 and 5. CONTINUE? appears in the remote's display. If SELECT KEY is flashing go back to step 4. 6 If you want to program in more commands use the 5∞ buttons to select YES. Press ENTER. Repeat steps 4 and 5 to teach the remote control of the VSX-45TX all the commands from the other remote control. 7 If you want to program in commands for another MULTI CONTROL button use the 5∞ buttons to select NO. Press ENTER. memo • If FULL appears in step 5 it means that there isn't enough capacity to learn this command. If you want to clear other buttons to make room for this one follow the procedure on page 87. • If there isn't enough capacity, an incorrect signal has been sent or, in some cases, the command from another remote control simply cannot be learned, NG (no good) will appear in the display in step 5. 8 Repeat the process from step 2 for all of your components. Start again to program other components in this manner. 9 When you're done use the 5∞ buttons to select EXIT. You will return to the REMOTE SETUP menu. 10 Select EXIT and press ENTER. • In some NG cases the remotes just need to be moved closer together or farther apart. BASIC 65