Pioneer VSX-45TX Owner's Manual - Page 98
FINE CHANNEL LEVEL should
View all Pioneer VSX-45TX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 98 highlights
Fine Tuning Your System FINE CHANNEL LEVEL The following steps show you how to balance the sound output level of your speakers more finely than in the NORMAL setup (see page 42). Proper speaker balance is essential for obtaining high quality surround sound and the better the speaker balance the better surround sound you can get. Do this procedure if you want to try and get even finer surround sound. The main difference with this setup method and the CHANNEL LEVEL setup method in NORMAL setup is that here the test tone alternates between the front left speaker (which is used as the reference channel) and the target speaker (that is, the speaker whose level you want to adjust). Listen to the two tones and try to make them the same volume. DIMMER LOUDNESS 1 2 TONE EFFECT/CH SEL 3 4 SIGNAL SEL 5 VIDEO SEL 9 DNR BASS/TREBLE + 6 7 8 HI-BIT +10 - DISC 0 ENTER SYSTEM SETUP DIRECT ACCESS SEARCH MODE GUIDE MENU TOP MENU TUNER EDIT ENTER TRACK EXIT AUDIO RETURN MPX ¶ TUNING - 1 STATION - 4 CHANNEL - DTV ON/OFF 8 BAND 3 DTV MENU CLASS 7 DISP MODE SUB TITLE TUNING + ¡ STATION + ¢ CHANNEL+ 1-5 1-5 STANDBY/ON MOVIE MUSIC ENTER MULTI JOG STANDBY MULTI JOG CONTROL SET UP RETURN SIGNAL HI-BIT SELECT HI-SAMPLING SB CH MODE BAND PHONES SPEAKERS TONE TONE CONTROL BASS/TREBLE 1 Expert [Crossover Network ] [Fine Channel Level ] [Fine Channel Delay ] [Acoustic Cal EQ ] [Bass Peak Level ] [D-Range Control ] [Exit ] 2 Fine Channel Level STD:Front L +1. 5dB Front R Center Surround L Surround R SurrBack L SurrBack R Subwoofer [Exit ] [ +1. 5dB] [ +1. 5dB] [ +2. 0dB] [ -1. 5dB] [ +3. 0dB] [ +2. 0dB] [+10. 0dB] Follow steps 1-5 on page 96, if necessary, to get to the starting point mentioned here. 1 FINE CHANNEL LEVEL should be selected, if it isn't use the 5∞ buttons to select and press ENTER. 2 Use the 5∞ buttons to select the channel you want to adjust. Press ENTER. Test tones will be output. WARNING : Be prepared! The test tones are output at a high volume level. MASTER VOLUME rotates to the reference position (0 dB) and the display on the receiver flashes TEST TONE. After a few seconds the test tone is output. 3 Adjust the level of the channel using the 5∞ buttons. Try to get the volume level of the target speaker to match that of the front left speaker, which is the reference in this setup. The levels can be set within a range of -10 dB to +10 dB in 0.5 dB steps. When you press ENTER you will automatically go to the next channel. 4 Press ENTER to select a new channel. Repeat step 3 for every channel. If you want to change a setting before proceeding Use the 5∞ buttons to go back to the channel you want to adjust and press ENTER. Then follow step 3. 5 When done select EXIT (if it's not already selected) and press ENTER. Next, if you want, proceed to FINE CHANNEL DELAY. 3 98 Fine Channel Level STD:Front L +1. 5dB Front R Center Surround L Surround R SurrBack L SurrBack R Subwoofer [Exit ] [ +2. 5dB] [ +1. 5dB] [ +2. 0dB] [ -1. 5dB] [ +3. 0dB] [ +2. 0dB] [+10. 0dB] 5 Fine Channel Level STD:Front L +1. 5dB Front R Center Surround L Surround R SurrBack L SurrBack R Subwoofer [Exit ] [ +2. 5dB] [ +1. 5dB] [ +2. 0dB] [ -1. 5dB] [ +3. 0dB] [ +2. 0dB] [+10. 0dB]