Sanyo PDG-DHT8000L RS232C Expand - Page 29

CF_DLINE Command, 5.8 CF_SETPCADJ Command, 5.9 CF_ORGMODE Command

Get Sanyo PDG-DHT8000L - 8000 Lumens PDF manuals and user guides View all Sanyo PDG-DHT8000L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

PDG-DHT8000L Expand Serial Command Functional Specifications 8.5.7 CF_DLINE Command Command "CF_DLINE_%1" [CR] "0100-nnnn Directly specify setting value of Display Line %1 "nnnn" indicates maximum value, which is current value of (Total Line - Position V). "UP Increment setting value of Display Line by 1 "DN Decrement setting value of Display line by 1 Details Set setting value of Display Line in PC signal (Available only in the normal Power ON status). The value set by this command is not being stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.) Acceptable Response Unacceptable "000" [CR] "101" [CR] --- When input is Video signal --- When input is no signal 8.5.8 CF_SETPCADJ Command Command "CF_SETPCADJ_%1" [CR] %1 "XGA1", "HDTV1080", "MODE1 Etc. "EXT11"~"EXT60" Detail Note1) When "XGA","HDTV1080","MODE1" is specified in %1, the command is not executed. Note2) When "EXTn-EXTnn" (nn represents number) is specified in %1, "EXT" is displayed in "SYSTEM" menu (only when Network board is provided). Acceptable Response "000" [CR] Unacceptable "101" [CR] --- When input is Video signal 8.5.9 CF_ORGMODE Command Command "CF_ORGMODE_%1" [CR] When input signal is PC Analog; "VGA1 Specify VGA1 : "WXGA3 Specify WXGA3 "1080I60 Specify 1080i60 "1080I50 Specify 1080i50 "1035I Specify 10350i "720p60 Specify 720p60 "720p50 Specify 720p50 %1 "575p Specify 575p "480p Specify 480p "575I Specify 575i "480I Specify 480i "1080psf/24 Specify 1080psf/24 "1080psf/25 Specify 1080psf/25 "1080psf/30 Specify 1080psf/30 "1080p24 Specify 1080p24 : "1080p60 Specify 1080p60 * When input signal is not PC Analog, error code "101" is returned. Details After "EXT n" is set by PC control command such as CF_FSYNC/CF_TDOTS and CF_SETPCADJ command, specify the signal originated with by issuing this command. This command is used to specify projector internal settings such as whether or not to get PC signal through IP (Available only in the normal Power ON status) Note; To differentiate between 60Hz and 50Hz in 1080i and 720p, "60" or "50" is necessary to add to the parameter in this command. Acceptable Response Unacceptable "000" [CR] "101" [CR] --- When input is Video signal 29/101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
PDG-DHT8000L
Expand Serial Command Functional Specifications
29/101
8.5.7 CF_DLINE Command
Command
“CF_DLINE_%1” [CR]
%1
“0100-nnnn” ----------- Directly specify setting value of Display Line
“nnnn” indicates maximum value, which is current value of (Total Line - Position V).
“UP” ------------------- Increment setting value of Display Line by 1
“DN” ------------------- Decrement setting value of Display line by 1
Details
Set setting value of Display Line in PC signal (Available only in the normal Power
ON status). The value set by this command is not being stored in the projector’s
memory. Therefore, when the power is turned to ALL OFF status, the value
returns to the original setting. (It is stored in Suspend mode.)
Acceptable
“000” [CR]
Response
Unacceptable
“101” [CR] --- When input is Video signal
--- When input is no signal
8.5.8 CF_SETPCADJ Command
Command
“CF_SETPCADJ_%1” [CR]
%1
“XGA1”, “HDTV1080”, “MODE1”
....................................
Etc.
“EXT11“~“EXT60“
Detail
Note1) When “XGA”,”HDTV1080”,”MODE1” is specified in %1, the command is not
executed.
Note2) When “EXTn-EXTnn” (nn represents number) is specified in %1, “EXT” is
displayed in “SYSTEM” menu (only when Network board is provided).
Acceptable
“000” [CR]
Response
Unacceptable
“101” [CR] --- When input is Video signal
8.5.9 CF_ORGMODE Command
Command
“CF_ORGMODE_%1” [CR]
%1
When input signal is PC Analog;
“VGA1” ------------------------ Specify VGA1
:
“WXGA3” --------------------- Specify WXGA3
“1080I60” --------------------- Specify 1080i60
“1080I50” --------------------- Specify 1080i50
“1035I” ------------------------ Specify 10350i
“720p60” --------------------- Specify 720p60
“720p50” --------------------- Specify 720p50
“575p” ------------------------- Specify 575p
“480p” ------------------------- Specify 480p
“575I” -------------------------- Specify 575i
“480I” -------------------------- Specify 480i
“1080psf/24” ----------------- Specify 1080psf/24
“1080psf/25” ----------------- Specify 1080psf/25
“1080psf/30” ----------------- Specify 1080psf/30
“1080p24” -------------------- Specify 1080p24
:
“1080p60” -------------------- Specify 1080p60
* When input signal is not PC Analog, error code “101” is returned.
Details
After “EXT n” is set by PC control command such as CF_FSYNC/CF_TDOTS and
CF_SETPCADJ command, specify the signal originated with by issuing this
command.
This command is used to specify projector internal settings such as whether or not
to get PC signal through IP (Available only in the normal Power ON status)
Note; To differentiate between 60Hz and 50Hz in 1080i and 720p, “60” or “50” is
necessary to add to the parameter in this command.
Acceptable
“000” [CR]
Response
Unacceptable
“101” [CR] --- When input is Video signal