Sanyo PDG-DHT8000L RS232C Expand - Page 78

Lamp Status Read Commands, 9.1 CR_LAMPREPL Command, 9.2 CR_LAMPMODE Command, 9.3 CR_AUTOLAMPCONTRL

Get Sanyo PDG-DHT8000L - 8000 Lumens PDF manuals and user guides View all Sanyo PDG-DHT8000L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

PDG-DHT8000L Expand Serial Command Functional Specifications 9.9 Lamp Status Read Commands 9.9.1 CR_LAMPREPL Command Command "CR_LAMPREPL" [CR] Details Get the information of Lamp Replacement time Acceptable "000_%1" [CR] "2**" 2 indicates 2 lamps are used in this model. indicates the status of each lamp in lamp number order. Response %1 "Y" means the lamp operating time is over the threshold for lamp replacement, and "N" means it has not reached to. e.g. "2YN This indicates it is 2-lamp system, and Lamp #2 has not been reached to the replacement time while #1 should be replaced. Unacceptable "?" [CR] 9.9.2 CR_LAMPMODE Command Command "CR_LAMPMODE" [CR] Details Get Lamp mode setting status Acceptable "000_%1" [CR] "FULL Lamp mode is set to 2-lamp (FULL) Response %1 "LAMP1 Lamp mode is set to Lamp1 "LAMP2 Lamp mode is set to Lamp2 Unacceptable "?" [CR] 9.9.3 CR_AUTOLAMPCONTRL Command Command "CR_AUTOLAMPCONTRL" [CR] Details Get selected Lamp control mode Acceptable "000_%1" [CR] Response "NORMAL NORMAL is selected. %1 "ECO1 ECO1 is selected. "ECO2 ECO2 is selected. Unacceptable "Error Code" [CR] 9.9.4 CR_LAMPSTS Command Command "CR_LAMPSTS" [CR] Details Get the information of Lamp lighting status Acceptable "000_%1" [CR] "2**" The first character indicates 2 lamps are used in this model. The following characters indicate each lamp status in lamp number order as showed below. Response %1 "I Lamp is ON "O Lamp is OFF "X Lamp Failure e.g. "2IO This indicates it is 2-lamps system, Lamp #1 is ON, and #2 is OFF. Unacceptable "?" [CR] 78/101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
PDG-DHT8000L
Expand Serial Command Functional Specifications
78/101
9.9
Lamp Status Read Commands
9.9.1 CR_LAMPREPL Command
Command
“CR_LAMPREPL” [CR]
Details
Get the information of Lamp Replacement time
Acceptable
“000_%1” [CR]
%1
“2**”
2 ---------------- indicates 2 lamps are used in this model.
* ---------------- indicates the status of each lamp in lamp number
order.
“Y” means the lamp operating time is over the
threshold for lamp replacement, and “N” means
it has not reached to.
e.g.
“2YN” ------------ This indicates it is 2-lamp system, and Lamp #2
has not been reached to the replacement time
while #1 should be replaced.
Response
Unacceptable
“?” [CR]
9.9.2 CR_LAMPMODE Command
Command
“CR_LAMPMODE” [CR]
Details
Get Lamp mode setting status
Acceptable
“000_%1” [CR]
%1
“FULL” ---------------- Lamp mode is set to 2-lamp (FULL)
“LAMP1”-------------- Lamp mode is set to Lamp1
“LAMP2” ------------- Lamp mode is set to Lamp2
Response
Unacceptable
“?” [CR]
9.9.3 CR_AUTOLAMPCONTRL Command
Command
“CR_AUTOLAMPCONTRL” [CR]
Details
Get selected Lamp control mode
Acceptable
“000_%1” [CR]
%1
“NORMAL” ---------- NORMAL is selected.
“ECO1” --------------- ECO1 is selected.
“ECO2” --------------- ECO2 is selected.
Response
Unacceptable
“Error Code” [CR]
9.9.4 CR_LAMPSTS Command
Command
“CR_LAMPSTS” [CR]
Details
Get the information of Lamp lighting status
Acceptable
“000_%1” [CR]
%1
“2**”
The first character indicates 2 lamps are used in this model.
The following characters indicate each lamp status in lamp
number order as showed below.
“I” ------------------------ Lamp is ON
“O” ---------------------- Lamp is OFF
“X” ----------------------- Lamp Failure
e.g.
“2IO” ------------------- This indicates it is 2-lamps system, Lamp
#1 is ON, and #2 is OFF.
Response
Unacceptable
“?” [CR]