Sanyo PDG-DHT8000L RS232C Expand - Page 49

CF_DYNAMICBLACK Command, 9.39 CF_HDMISETUP Command, 9.40 CF_LOGO Command

Get Sanyo PDG-DHT8000L - 8000 Lumens PDF manuals and user guides View all Sanyo PDG-DHT8000L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

PDG-DHT8000L Expand Serial Command Functional Specifications 8.9.38 CF_DYNAMICBLACK Command Command "CF_DYNAMICBLACK_%1" [CR] "OFF Set to Off %1 "LOW Set to Low "HIGH Set to High Details Set status of DynamicBlack.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status. Acceptable Response "000" [CR] Unacceptable "Error Code" [CR] 8.9.39 CF_HDMISETUP Command Command "CF_HDMISETUP_%1" [CR] %1 "NORMAL Set to Normal "ENHANCED Set to Enhanced Details Set status of HDMI setup.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status. Acceptable Response "000" [CR] Unacceptable "Error Code" [CR] 8.9.40 CF_LOGO Command Command "CF_LOGO_%1_%2" [CR] %1 "0000 - 9999 Directly set Logo PIN code "OFF Cancel Logo display "DFLT Select Logo of Factory Default "USER Select User %2 "UP Select functions to choose forward (OFF → DFLT → USER → OFF → --) "DN Select functions to choose backward (OFF → USER → DFLT → OFF → --) Set Logo mode.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status. Set Logo PIN code in %1. Details *When Logo Lock is enabled: PIN code is matched Command is valid (Acceptable) PIN code is mismatched Command is invalid (Error code "102") PIN code is beyond %1 available range Command is invalid (Error code"?") *When Logo Lock is disabled: PIN code is within %1 available range ------- Command is valid (Acceptable) PIN code is out of %1 available range ------- Command is invalid (Error code "?") Note: When Logo Lock is enabled, matching Logo PIN code switches Logo but Logo Lock is not cancelled (Lock status is kept). *When 2="USER" is received, error code "101" is returned, in the case of Capture non-practice. Acceptable Response "000" [CR] Unacceptable "Error Code" [CR] 49/101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
PDG-DHT8000L
Expand Serial Command Functional Specifications
49/101
8.9.38 CF_DYNAMICBLACK Command
Command
“CF_DYNAMICBLACK_%1” [CR]
%1
“OFF” --------------------- Set to Off
“LOW” -------------------- Set to Low
“HIGH” ------------------- Set to High
Details
Set status of DynamicBlack.(Available only in the normal Power ON status)
The status set by this command is stored in EEPROM and the setting remains
effective after the power is turned to ALL OFF status.
Acceptable
“000” [CR]
Response
Unacceptable
“Error Code” [CR]
8.9.39 CF_HDMISETUP Command
Command
“CF_HDMISETUP_%1” [CR]
%1
“NORMAL” ---------------------- Set to Normal
“ENHANCED” ------------------ Set to Enhanced
Details
Set status of HDMI setup.(Available only in the normal Power ON status)
The status set by this command is stored in EEPROM and the setting remains
effective after the power is turned to ALL OFF status.
Acceptable
“000” [CR]
Response
Unacceptable
“Error Code” [CR]
8.9.40 CF_LOGO Command
Command
“CF_LOGO_%1_%2” [CR]
%1
“0000 – 9999” ------------- Directly set Logo PIN code
%2
“OFF” ---------------------------Cancel Logo display
“DFLT” ------------------------- Select Logo of Factory Default
“USER” ------------------------ Select User
“UP” ---------------------------- Select functions to choose forward
(OFF
→
DFLT
→
USER
→
OFF
→
--)
“DN” ---------------------------- Select functions to choose backward
(OFF
→
USER
→
DFLT
→
OFF
→
--)
Details
Set Logo mode.(Available only in the normal Power ON status)
The status set by this command is stored in EEPROM and setting remains
effective even after the power is turned to ALL OFF status.
Set Logo PIN code in %1.
*When Logo Lock is enabled:
PIN code is matched ------------------------- Command is valid (Acceptable)
PIN code is mismatched-------------------- Command is invalid (Error code “102”)
PIN code is beyond %1 available range ------------ Command is invalid (Error
code”?”)
*When Logo Lock is disabled:
PIN code is within %1 available range ------- Command is valid (Acceptable)
PIN code is out of %1 available range ------- Command is invalid (Error code “?”)
Note: When Logo Lock is enabled, matching Logo PIN code switches Logo but
Logo Lock is not cancelled (Lock status is kept).
*When
�
2=”USER” is received, error code “101” is returned, in the case of
Capture non-practice.
Acceptable
“000” [CR]
Response
Unacceptable
“Error Code” [CR]