Sanyo PDG-DHT8000L RS232C Expand - Page 35

CF_REAR Command, 7.7 CF_VSCALE Command, 7.8 CF_VPOS Command

Get Sanyo PDG-DHT8000L - 8000 Lumens PDF manuals and user guides View all Sanyo PDG-DHT8000L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

PDG-DHT8000L Expand Serial Command Functional Specifications 8.7.6 CF_REAR Command Command "CF_REAR_%1" [CR] %1 "ON Set Rear to ON "OFF Set Rear to OFF Details Set/Cancel Rear. (Valid only when in the normal Power ON status.) When Rear is set to ON, image is left/right reversed. The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status. Acceptable Response Unacceptable "000" [CR] "Error Code" [CR] 8.7.7 CF_VSCALE Command Command "CF_VSCALE_%1" [CR] "035 35 "031 31 "001 1 "000 0 %1 " 01 1 Details Response " 31 31 " 32 32 "UP Increment setting value of Vscale by 1 "DN Decrement setting value of Vscale by 1 Set Vscale (Available only in the normal Power ON status) *When selected screen mode is a setting except Custom, return "101" [CR] and the command is not executed. * When input is no signal, return "101" [CR] and the command is not executed. Acceptable "000" [CR] Unacceptable "Error Code" [CR] 8.7.8 CF_VPOS Command Command "CF_VPOS_%1" [CR] "015 15 "014 14 "001 1 "000 0 %1 " 01 1 Details Response " 14 14 " 15 15 "UP Increment setting value of Vposition by 1 "DN Decrement setting value of Vposition by 1 Set V Position (Available only in the normal Power ON status) *When selected screen mode is a setting except Custom, return "101" [CR] and the command is not executed. * When input is no signal, return "101" [CR] and the command is not executed. Acceptable "000" [CR] Unacceptable "Error Code" [CR] 35/101

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
PDG-DHT8000L
Expand Serial Command Functional Specifications
35/101
8.7.6 CF_REAR Command
Command
“CF_REAR_%1” [CR]
%1
“ON” --------------------------- Set Rear to ON
“OFF” ------------------------- Set Rear to OFF
Details
Set/Cancel Rear. (Valid only when in the normal Power ON status.)
When Rear is set to ON, image is left/right reversed.
The status set by this command is stored in EEPROM and the setting remains
effective after the power is turned to ALL OFF status.
Acceptable
“000” [CR]
Response
Unacceptable
“Error Code” [CR]
8.7.7 CF_VSCALE Command
Command
“CF_VSCALE_%1” [CR]
%1
“035” ---------------------- +35
“031” ---------------------- +31
�
“001” ---------------------- +1
“000” ---------------------- ±0
“
�
01” ---------------------
�
1
�
“
�
31” ---------------------
�
31
“
�
32” ---------------------
�
32
“UP” --------------------- Increment setting value of Vscale by 1
“DN” --------------------- Decrement setting value of Vscale by 1
Details
Set Vscale (Available only in the normal Power ON status)
*When selected screen mode is a setting except Custom, return “101” [CR] and
the command is not executed.
* When input is no signal, return “101” [CR] and the command is not executed.
Acceptable
“000” [CR]
Response
Unacceptable
“Error Code” [CR]
8.7.8 CF_VPOS Command
Command
“CF_VPOS_%1” [CR]
%1
“015” --------------------- +15
“014” --------------------- +14
�
“001” --------------------- +1
“000” --------------------- ±0
“
�
01” ---------------------
�
1
�
“
�
14” ---------------------
�
14
“
�
15” ---------------------
�
15
“UP” --------------------- Increment setting value of Vposition by 1
“DN” --------------------- Decrement setting value of Vposition by 1
Details
Set V Position (Available only in the normal Power ON status)
*When selected screen mode is a setting except Custom, return “101” [CR] and
the command is not executed.
* When input is no signal, return “101” [CR] and the command is not executed.
Acceptable
“000” [CR]
Response
Unacceptable
“Error Code” [CR]