Sharp MX-M350N Fax Guide - Page 78
Storing A Program, Editing And Deleting Programs
![]() |
View all Sharp MX-M350N manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 78 highlights
STORING, EDITING, AND DELETING AUTO DIAL KEYS AND PROGRAMS STORING A PROGRAM You can store a destination fax number, speed dialing, polling, erase, dual page scan, 2in1, card shot, and resolution and exposure settings in a program. This enables you to call up the program and perform the transmission by means of a simplified operation. (See "USING A PROGRAM" on page 3-17.) NOTE A timer setting (page 3-6) cannot be included in a program. When storing a program for an F-Code operation, one touch keys for destinations must include sub-addresses. To store a program key, follow steps 1 through 3 on page 6-2, touch the [PROGRAM] key in step 4, and then follow these steps. 1 Touch the [PROGRAM NAME] key. For the detailed procedures for each of the settings, refer to the explanations of those features on the following pages. PROGRAM The "No." that No.1 automatically appears is PROGRAM NAME SETTINGS ADDRESS the lowest number from 1 to 8 that has not yet been programmed. When the RESOLUTION [PROGRAM NAME] key is touched, the letter-entry screen appears. Enter up to 18 characters for the name. Refer to chapter 7 of "Operation manual (for general information and copier operation)" for the procedure for entering letters. 2 Touch the [SETTINGS] key. [RESOLUTION](page 1-10) [EXPOSURE](page 1-11) [SPEED DIAL](page 2-4) [ADDRESS BOOK] (page 3-3) [SPECIAL MODES] ERASE (page 3-4) DUAL PAGE SCAN (page 3-5) 2in1 (page 3-7) CARD SHOT (page 3-8) POLLING (page 3-13) NOTE Up to 500 (maximum of 300 on the AR-M351U/ARM451U) destinations can be stored in a program. However, you cannot directly enter fax numbers with the numeric keys. A destination must be programmed in an auto dial key (one-touch key or group key) before it can be stored in a program. No.1 PROGRAM NAME PROGRAM FOR SHARP SETTINGS ADDRESS 4 Touch the [OK] key. 5 Your settings are displayed. Make sure they are correct. RESOLUTION SPECIAL MODES 3 Touch the keys for the settings you wish to store. PROGRAM No.1 REGISTRATION PROGRAM NAME SHARP PROGRAM SETTINGS ADDRESS 2 ADDRESSES RESOLUTION FINE NEXT EXIT EXPOSURE AUTO ENTER PROGRAM YOU REQUIRE. CANCEL OK SPECIAL MODES DUAL PAGE SCAN AUTO EXPOSURE STANDARD RESOLUTION FAX MODE SWITCH ADDRESS BOOK ADDRESS REVIEW SPECIAL MODES 6 When you are finished, touch the [EXIT] key. If you wish to store another program, touch the [NEXT] key. Touching the [EXIT] key returns you to the screen of step 4 on page 6-2. Touching the [NEXT] key returns you to the screen of step 1. EDITING AND DELETING PROGRAMS To edit or delete a previously stored program, follow steps 1 to 3 on page 6-2, touch the [AMEND/DELETE] key in the screen of step 4, and then follow these steps. 1 Touch the [PROGRAM] key. 2 Touch the program you wish to edit or delete. EXIT 1/2 PROGRAM DIRECT ADDRESS / AMEND/DELETE SELECT ADDRESS TO AMEND/DELETE. PROGRAM PROGRAM FOR SHARP EMAIL NEWS GROUP EXIT ADDRESS BOOK ABYS FAX FORMAT A 6-8 Downloaded From ManualsPrinter.com Manuals When you touch the program name, the edit/delete screen for the selected program appears. Touching the [ADDRESS BOOK] key returns you to the screen of step 1. 3 To edit the program, follow the same procedure as for storing the program. To delete the program, touch the [DELETE] key and then touch the [YES] key in the confirmation screen that appears.
![](/manual_guide/products/sharp-mxm350n-fax-guide-4035d29/78.png)