TP-Link 13dBi CPE510 V1 UG - Page 57

Bandwidth Control, AP router, AP client router WISP, Client - cpe510

Get TP-Link 13dBi PDF manuals and user guides View all TP-Link 13dBi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Static Routing Chapter 5 Network Tab Check the Enable box to use the static routing function. To use the static routing: 1. Click Add to create a new static routing. 2. Enter the Target Network IP, the address of the network or host to be visited. The IP address cannot be on the same network segment with the device's WAN or LAN port. 3. Enter the Netmask. 4. Enter the Gateway IP, the address of the gateway that allows for contact between the Device and the network or host. 5. Click OK after finishing the configuration. Select the added entries, you can edit or delete them. Bandwidth Control The function of Bandwidth Control is available only in AP router mode and AP client router (WISP Client) mode. Bandwidth control function is used to control the Internet bandwidth in the local area network. In the case of insufficient bandwidth resources, enable the function to make the device allocate reasonable bandwidth to the clients and achieve the purpose of efficient use of the existing bandwidth. Via IP bandwidth control function, you can set the upper and lower limit in the bandwidth of the computer network and guarantee a smooth sharing network. Total Ingress Bandwidth The total download speed limited through the WAN port. The maximum value of CPE510/CPE520/CPE210/CPE220 is 100,000kbps while that of BS510/BS210/OAP210 is 1,000,000kbps. Total Egress Bandwidth The total upload speed limited through the WAN port. The maximum value of CPE510/CPE520/CPE210/CPE220 is 100,000kbps while that of BS510/BS210/OAP210 is 1,000,000kbps. - 54 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Chapter 5 Network Tab
Static Routing
Check the
Enable
box to use the static routing function.
To use the static routing:
1.
Click
Add
to create a new static routing.
2.
Enter the
Target
Network IP
, the address of the network or host to be
visited. The IP address cannot be on the same network segment with the
device's WAN or LAN port.
3.
Enter
the
Netmask
.
4.
Enter the
Gateway IP
, the address of the gateway that allows for contact
between the Device and the network or host.
5.
Click
OK
after finishing the configuration.
Select the added entries, you can edit or delete them.
Bandwidth Control
The function of
Bandwidth Control
is available only in
AP router
mode and
AP client router (WISP
Client)
mode.
Bandwidth control function is used to control the Internet bandwidth in the local area network. In the case
of insufficient bandwidth resources, enable the function to make the device allocate reasonable
bandwidth to the clients and achieve the purpose of efficient use of the existing bandwidth. Via IP
bandwidth control function, you can set the upper and lower limit in the bandwidth of the computer
network and guarantee a smooth sharing network.
Total Ingress Bandwidth
The total download speed limited through the WAN port. The maximum value
of
CPE510/CPE520/CPE210/CPE220
is
100,000kbps
while
that
of
BS510/BS210/OAP210 is 1,000,000kbps.
Total Egress Bandwidth
The total upload speed limited through the WAN port. The maximum value of
CPE510/CPE520/CPE210/CPE220
is
100,000kbps
while
that
of
BS510/BS210/OAP210 is 1,000,000kbps.
- 54 -