TRENDnet TEW-816DRM User's Guide - Page 31

Backup 3G Enable

Get TRENDnet TEW-816DRM PDF manuals and user guides View all TRENDnet TEW-816DRM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

TRENDnet User's Guide PPPoE If you select PPPoE (RFC-2516 PPP over Ethernet) on the Protocol section, the screen below is displayed.  User Name: Enter the user name provided by your ISP.  User Password: Enter the password provided by your ISP.  Confirm Password: Re-enter the password.  Authentication Method: Select the type of authentication method to apply.  Dial-up Mode: Configure how you want your modem router to connect and terminate the Internet connection. Options are: © Copyright 2015 TRENDnet. All Rights Reserved. TEW-816DRM o OnDemand: Enables the modem router to cut off the Internet connection after being idle for a specified period of time. The device automatically re-establishes the connection when you try to access the Internet again. In the Idle Disconnect Time field, enter the number of seconds that you want to elapse before your modem router terminates the Internet connection. o AlwaysOn: Enables the modem router to be connected to the Internet at all times. If you are disconnected, the device will automatically re-establish the connection. o Manual: Manually configure this setting. Enter the user name and password to establish the Internet connection.  Inactivity Time: View the preset idle time before the session is disconnected.  MRU Size: Set the maximum rate of cells that you can receive. If provided by your ISP, enter the rate in the field. Otherwise, leave this field to its default setting.  MTU Size: Set the maximum rate of cells that you can receive. If provided by your ISP, enter the rate in the field. Otherwise, leave this field to its default setting.  Keep Alive: Select this option to maintain connection  LCP Interval: Enter the number of seconds that you want to be the interval in sending LCP (Link Control Protocol) packets.  Use Static IP Address: Select this option if you have an assigned static IP Address  IP Address: Enter your assigned static IP Address.  NAT: Select whether to enable or disable NAT (Network Address Translation). Enable this setting to share one WAN IP address with multiple computers on your network.  Enable Service: Select this option to enable  Backup 3G Enable: Select this option to enable 3G WAN backup connection.  Name: Enter your desired connection name. Bridge Mode If you select Bridge mode, the screen below is displayed. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
© Copyright 2015 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-816DRM
28
PPPoE
If you select PPPoE (RFC-2516 PPP over Ethernet) on the Protocol section, the screen
below is displayed.
User Name:
Enter the user name provided by your ISP.
User Password:
Enter the password provided by your ISP.
Confirm Password:
Re-enter the password.
Authentication Method: Select the type of authentication method to apply.
Dial-up Mode:
Configure how you want your modem router to connect and
terminate the Internet connection. Options are:
o
OnDemand:
Enables the modem router to cut off the Internet connection after
being idle for a specified period of time. The device automatically re-establishes
the connection when you try to access the Internet again. In the Idle Disconnect
Time field, enter the number of seconds that you want to elapse before your
modem router terminates the Internet connection.
o
AlwaysOn:
Enables the modem router to be connected to the Internet at all
times. If you are disconnected, the device will automatically re-establish the
connection.
o
Manual:
Manually configure this setting. Enter the user name and password to
establish the Internet connection.
Inactivity Time:
View the preset idle time before the session is disconnected.
MRU Size:
Set the maximum rate of cells that you can receive. If provided by your
ISP, enter the rate in the field. Otherwise, leave this field to its default setting.
MTU Size
: Set the maximum rate of cells that you can receive. If provided by your
ISP, enter the rate in the field. Otherwise, leave this field to its default setting.
Keep Alive:
Select this option to maintain connection
LCP Interval:
Enter the number of seconds that you want to be the interval in
sending LCP (Link Control Protocol) packets.
Use Static IP Address:
Select this option if you have an assigned static IP Address
IP Address: Enter your assigned static IP Address.
NAT:
Select whether to enable or disable NAT (Network Address Translation).
Enable this setting to share one WAN IP address with multiple computers on your
network.
Enable Service:
Select this option to enable
Backup 3G Enable:
Select this option to enable 3G WAN backup connection.
Name:
Enter your desired connection name.
Bridge Mode
If you select Bridge mode, the screen below is displayed.