Cisco 10720 Configuration Guide - Page 85

Activity, Description, RPR/SRP Uplink System LEDs, Table 3-4

Get Cisco 10720 - Internet Router PDF manuals and user guides View all Cisco 10720 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Chapter 3 Installing the Cisco 10720 Internet Router Verifying the Cisco 10720 Internet Router LEDs Table 3-4 DPT and POS/DPT Uplink Card System LEDs LED Activity Description OVERTEMP Green (default status when initialized) System is operating within the proper temperature range. (inlet

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
3-35
Cisco 10720 Internet Router Installation and Configuration Guide
78-13062-10
Chapter 3
Installing the Cisco 10720 Internet Router
Verifying the Cisco 10720 Internet Router LEDs
Figure 3-35
RPR/SRP Uplink System LEDs
Table 3-4
DPT and POS/DPT Uplink Card System LEDs
LED
Activity
Description
OVERTEMP
Green (default status
when initialized)
System is operating within the proper temperature
range.
(inlet <104
o
F [40
o
C]; outlet <109
o
F [43
o
C])
Red/Green
Both LEDs are on, appearing
orange
. Systems working
on warning temperature range.
(104
o
F [40
o
C] <= inlet < 122
o
F [50
o
C], 109
o
F [43
o
C] <=
outlet< 127
o
F [53
o
C])
Red
System is working on critical temperature state.
(122
o
F [50
o
C] <= inlet < 149
o
F [65
o
C], 127
o
F [53
o
C] <=
outlet < 167
o
F [75
o
C])
CARD FAIL
Red
A hardware failure is being detected on the uplink card.
During power up, the LED will be red, even when the
uplink card is powered down.
Off (default status when
initialized)
Card is operational. The LED is turned off after
hardware initialization.
SYSTEM STATUS
Red
Not applicable.
Red/Green
Both LEDs are on, appears orange. This is the normal
configuration during power up. Once the software loads
successfully, the red LED will turn off.
Green (default status
when initialized)
System is operational.
POWER
Green (default status
when initialized)
The uplink card is receiving power from the system
1
.
1.
System power up is not an indication that the uplink card is powered up. Check the card status LEDs to ensure the card is
functional properly and is receiving power form the system.
Off
Uplink card is not receiving power from the system.
2
CONSOLE
AUX
RESET
OVERTEMP
CARD FAIL
SYSTEM STATUS
POWER
ACTIVE
CARRIER
RX PKT
PASS THRU
PROTECT
1
10720-SR-LC
ACTIVE
CARRIER
RX PKT
PASS THRU
PROTECT
116786
OVERTEMP
CARD FAIL
SYSTEM STATUS
POWER