Cisco WRV210 Administration Guide - Page 47

Configuring a Wireless Distribution System (WDS - repeater mode

Get Cisco WRV210 PDF manuals and user guides View all Cisco WRV210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Configuring the Wireless Network Configuring a Wireless Distribution System (WDS) 3 After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. STEP 3 Click Save to save your settings, or click Cancel to refresh the page with the previously saved settings. Configuring a Wireless Distribution System (WDS) If you need to extend the coverage of the Router by using a repeater, you can use the WDS page to configure a Wireless Distribution System. This mode allows a wireless client to connect to the Router through an access point, such as WAP54GP or WAP54GPE, when operating in the Repeater Mode. You can install up to three repeaters. NOTE WDS works only with SSID1. Make sure that the channel and security settings are the same for all WDS-enabled devices. Cisco Small Business WRV210 Administration Guide 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Configuring the Wireless Network
Configuring a Wireless Distribution System (WDS)
Cisco Small Business WRV210 Administration Guide
47
3
After receiving an RTS, the wireless station responds with a Clear to Send
(CTS) frame to acknowledge the right to begin transmission.
STEP
3
Click
Save
to save your settings, or click
Cancel
to refresh the page with the
previously saved settings.
Configuring a Wireless Distribution System (WDS)
If you need to extend the coverage of the Router by using a repeater, you can use
the WDS page to configure a Wireless Distribution System. This mode allows a
wireless client to connect to the Router through an access point, such as
WAP54GP or WAP54GPE, when operating in the Repeater Mode. You can install
up to three repeaters.
NOTE
WDS works
only
with SSID1. Make sure that the channel and security settings are
the same for all WDS-enabled devices.