Cisco WS-C2960S-24TS-S Hardware Installation Guide - Page 66

Installing the Mounting Screws on a Wall, Step 4

Get Cisco WS-C2960S-24TS-S PDF manuals and user guides View all Cisco WS-C2960S-24TS-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Installing the Switch Chapter 3 Switch Installation (8-Port Switches) Figure 3-5 Installing the Mounting Screws on a Wall 1 2 TMHIOSUSNIDTIENAGWSAUYRFFRAOCEM 157828 CABLE SIDE ENTRY 2 3 2 1 Wall 3 Screw template 2 Screws Step 4 Step 5 Step 6 Step 7 Step 8 Attach the screw template to the wall. Use a 0.144-inch (3.7 mm) or a #27 drill bit to drill a 1/2-inch (12.7 mm) hole in the three screw template slots. Insert three screws in the slots on the screw template, and tighten until they touch the top of the screw template. Remove the screw template from the wall. Place the switch onto the mounting screws, and slide it down until it locks in place, as shown in Figure 3-6. 3-12 Catalyst 2960 Switch Hardware Installation Guide OL-7075-09

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
3-12
Catalyst 2960 Switch Hardware Installation Guide
OL-7075-09
Chapter 3
Switch Installation (8-Port Switches)
Installing the Switch
Figure 3-5
Installing the Mounting Screws on a Wall
Step 4
Attach the screw template to the wall.
Step 5
Use a 0.144-inch (3.7 mm) or a #27 drill bit to drill a 1/2-inch (12.7 mm) hole in the three screw
template slots.
Step 6
Insert three screws in the slots on the screw template, and tighten until they touch the top of the
screw template.
Step 7
Remove the screw template from the wall.
Step 8
Place the switch onto the mounting screws, and slide it down until it locks in place, as shown
in
Figure 3-6
.
1
Wall
3
Screw template
2
Screws
CABLE SIDE ENTRY
THIS SIDE AWAY FROM
MOUNTING SURFACE
2
3
2
2
1
157828