Cisco WS-C2960S-24TS-S Hardware Installation Guide - Page 90

Console Port, Cable and Adapter Specifications, SFP Module Cable Specifications

Get Cisco WS-C2960S-24TS-S PDF manuals and user guides View all Cisco WS-C2960S-24TS-S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Cable and Adapter Specifications Appendix B Connector and Cable Specifications Figure B-4 Pin 1 2 3 4 5 6 7 8 10/100/1000 Port Pinouts Label TP0+ TP0TP1+ TP2+ TP2TP1TP3+ TP3- 12345678 60915 Console Port The console port uses an 8-pin RJ-45 connector, which is described in Table B-2 and Table B-3. The supplied RJ-45-to-DB-9 adapter cable is used to connect the console port of the switch to a console PC. You need to provide a RJ-45-to-DB-25 female DTE adapter if you want to connect the switch console port to a terminal. You can order a kit (part number ACS-DSBUASYN=) containing that adapter from Cisco. For console port and adapter pinout information, see Table B-2 and Table B-3. Cable and Adapter Specifications These sections describe the cables and adapters used with Catalyst 2960 switches: • SFP Module Cable Specifications, page B-4 • Two Twisted-Pair Cable Pinouts, page B-6 • Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports, page B-6 • Crossover Cable and Adapter Pinouts, page B-7 SFP Module Cable Specifications Table B-1 lists the cable specifications for the fiber-optic SFP module connections. Each port must match the wave-length specifications on the other end of the cable, and for reliable communications, the cable must not exceed the required cable length. Copper 1000BASE-T SFP transceivers use standard four twisted-pair, Category 5 or greater cable at lengths up to 328 feet (100 meters). Catalyst 2960 Switch Hardware Installation Guide B-4 OL-7075-09

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
B-4
Catalyst 2960 Switch Hardware Installation Guide
OL-7075-09
Appendix B
Connector and Cable Specifications
Cable and Adapter Specifications
Figure B-4
10/100/1000 Port Pinouts
Console Port
The console port uses an 8-pin RJ-45 connector, which is described in
Table B-2
and
Table B-3
. The
supplied RJ-45-to-DB-9 adapter cable is used to connect the console port of the switch to a console PC.
You need to provide a RJ-45-to-DB-25 female DTE adapter if you want to connect the switch console
port to a terminal. You can order a kit (part number ACS-DSBUASYN=) containing that adapter from
Cisco. For console port and adapter pinout information, see
Table B-2
and
Table B-3
.
Cable and Adapter Specifications
These sections describe the cables and adapters used with Catalyst 2960 switches:
•
SFP Module Cable Specifications, page B-4
•
Two Twisted-Pair Cable Pinouts, page B-6
•
Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports, page B-6
•
Crossover Cable and Adapter Pinouts, page B-7
SFP Module Cable Specifications
Table B-1
lists the cable specifications for the fiber-optic SFP module connections. Each port must
match the wave-length specifications on the other end of the cable, and for reliable communications, the
cable must not exceed the required cable length. Copper 1000BASE-T SFP transceivers use standard
four twisted-pair, Category 5 or greater cable at lengths up to 328 feet (100 meters).
60915
23
1
45678
Pin
Label
1
2
3
4
5
6
7
8
TP0+
TP0-
TP1+
TP2+
TP2-
TP1-
TP3+
TP3-