D-Link DES-3226SM Product Manual - Page 27

Stacking with DGS-3212SR or DGS-3312SR

Get D-Link DES-3226SM - 1000Mbps Ethernet Switch PDF manuals and user guides
UPC - 790069247118
View all D-Link DES-3226SM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

DES-3226S Layer 2 Fast Ethernet Switch User's Guide Stacking with DGS-3212SR or DGS-3312SR The DES-3226S Release 4.01 Switch can be arranged in a star topology and managed as slave devices through either the DGS3212SR or DGS-3312SR Master Switch. Up to eight Switches can be connected to the DGS-3x12SR series Switch in this arrangement. Figure 5 - 1. DES-3226S Switches with DGS-3212SR Setting up a star topology with a DGS-3212SR or DGS-3312SR is a simple matter. Each DES-3226S connects to the master through the stacking port to a similar stacking port on a DGS-3x12SR series Switch equipped with one or two special stacking modules designed for the DGS-3x12SR series Switch. Each DES-3226S slave must be configured with stacking mode enabled. When stacked in a star topology arrangement with the DGS-3x12SR, the Switch will automatically assume slave status. The unit number is determined by the port number to which it is connected on the DGS-3x12SR master. The DGS-3x12SR must have a stacking module installed and have stacking mode enabled as well. Stacking for the DGS-3x12SR uses the identical CLI command: config stacking mode enable. Be sure to save the configuration change using the CLI command save. Remember that for star topology arrangements, if the stacking link to a given Switch fails or is disconnected, that Switch will loose its status in the stack and reboot as a standalone device with the IP settings. The DGS-3212SR/DGS-3312SR and remaining slave units are not effected by the link failure. NOTE: The DES-3226S must have stacking mode enabled to be used with the DGS-3212SR or the DGS-3312SR in a star topology arrangement. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
DES-3226S Layer 2 Fast Ethernet Switch User’s Guide
24
Stacking with DGS-3212SR or DGS-3312SR
The DES-3226S Release 4.01 Switch can be arranged in a star topology and managed as slave devices through either the DGS-
3212SR or DGS-3312SR Master Switch. Up to eight Switches can be connected to the DGS-3x12SR series Switch in this
arrangement.
Figure 5 - 1. DES-3226S Switches with DGS-3212SR
Setting up a star topology with a DGS-3212SR or DGS-3312SR is a simple matter. Each DES-3226S connects to the master
through the stacking port to a similar stacking port on a DGS-3x12SR series Switch equipped with one or two special stacking
modules designed for the DGS-3x12SR series Switch. Each DES-3226S slave must be configured with stacking mode enabled.
When stacked in a star topology arrangement with the DGS-3x12SR, the Switch will automatically assume slave status. The
unit number is determined by the port number to which it is connected on the DGS-3x12SR master. The DGS-3x12SR must
have a stacking module installed and have stacking mode enabled as well. Stacking for the DGS-3x12SR uses the identical
CLI command:
config stacking mode enable
.
Be sure to save the configuration change using the CLI command
save
.
Remember that for star topology arrangements, if the stacking link to a given Switch fails or is disconnected, that Switch will
loose its status in the stack and reboot as a standalone device with the IP settings. The DGS-3212SR/DGS-3312SR and
remaining slave units are not effected by the link failure.
NOTE:
The DES-3226S must have stacking mode enabled to be used with the DGS-3212SR or the
DGS-3312SR in a star topology arrangement.