HP Cisco Nexus 5000 Cisco MDS 9000 Family Fabric Manager Quick Configuration G - Page 22

setup, Enter, Cisco MDS 9000 Family Configuration Guide

Get HP Cisco Nexus 5000 - Converged Network Switches PDF manuals and user guides View all HP Cisco Nexus 5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Using the Switch Setup Utility Chapter 2 Initial Switch Configuration Send documentation comments to [email protected] Step 4 General Software Pentium III Embedded BIOS 2000 (tm) Revision 1.1.(0) (C) 2002 General Software, Inc.ware, Inc. Pentium III-1.1-6E69-AA6E | System BIOS Configuration, (C) 2002 General Software, Inc. | | System CPU : Pentium III | Low Memory : 630KB | | Coprocessor : Enabled | Extended Memory : 1018MB | | Embedded BIOS Date : 10/24/03 | ROM Shadowing : Enabled | Loader Loading stage1.5. Loader loading, please wait... Auto booting bootflash:/m9500-sf1ek9-kickstart-mz.2.1.1a.bin bootflash:/m9500-s f1ek9-mz.2.1.1a.bin... Booting kickstart image: bootflash:/m9500-sf1ek9-kickstart-mz.2.1.1a.bin Image verification OK Starting kernel... INIT: version 2.78 booting Checking all filesystems..... done. Loading system software Uncompressing system image: bootflash:/m9500-sf1ek9-mz.2.1.1a.bin CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC INIT: Entering runlevel: 3 Make sure you enter the password you wish to assign for the admin username. ---- System Admin Account Setup ---Enter the password for "admin": Tip If you create a password that is short and easy to decipher, then your password is rejected. Be sure to configure a strong password. Passwords are case-sensitive. You must explicitly configure a password that meets the requirements listed in the "Configuring User Accounts" section in the Cisco MDS 9000 Family Configuration Guide. Note If you are running the switch setup utility for the first-time, it starts automatically. If this is not the first-time configuration, you are required to enter setup at the system prompt. Note If you do not wish to answer a previously configured question, or if you wish to skip answers to any questions, press Enter. If a default answer is not available (for example, the switch name), the switch uses what was previously configured and skips to the next question. Step 5 Enter yes to enter setup mode. This setup utility will guide you through the basic configuration of the system. Setup configures only enough connectivity for management of the system. *Note: setup is mainly used for configuring the system initially, when no configuration is present. So setup always assumes system defaults and not the current system configuration values. Press Enter at anytime to skip a dialog. Use ctrl-c at anytime to skip the remaining dialogs. Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide 2-6 OL-7765-05

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Send documentation comments to [email protected]
2-6
Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide
OL-7765-05
Chapter 2
Initial Switch Configuration
Using the Switch Setup Utility
General Software Pentium III Embedded BIOS 2000 (tm) Revision 1.1.(0)
(C) 2002 General Software, Inc.ware, Inc.
Pentium III-1.1-6E69-AA6E
+------------------------------------------------------------------------------+
|
System BIOS Configuration, (C) 2002 General Software, Inc.
|
+---------------------------------------+--------------------------------------+
| System CPU
: Pentium III
| Low Memory
: 630KB
|
| Coprocessor
: Enabled
| Extended Memory
: 1018MB
|
| Embedded BIOS Date
: 10/24/03
| ROM Shadowing
: Enabled
|
+---------------------------------------+--------------------------------------+
Loader Loading stage1.5.
Loader loading, please wait...
Auto booting bootflash:/m9500-sf1ek9-kickstart-mz.2.1.1a.bin bootflash:/m9500-s
f1ek9-mz.2.1.1a.bin...
Booting kickstart image:
bootflash:/m9500-sf1ek9-kickstart-mz.2.1.1a.bin
...................
Image verification OK
Starting kernel...
INIT: version 2.78 booting
Checking all filesystems
.....
done.
Loading system software
Uncompressing system image: bootflash:/m9500-sf1ek9-mz.2.1.1a.bin
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
INIT: Entering runlevel: 3
Step 4
Make sure you enter the password you wish to assign for the admin username.
---- System Admin Account Setup ----
Enter the password for "admin":
Tip
If you create a password that is short and easy to decipher, then your password is rejected. Be
sure to configure a strong password. Passwords are case-sensitive. You must explicitly configure
a password that meets the requirements listed in the “Configuring User Accounts” section in the
Cisco MDS 9000 Family Configuration Guide
.
Note
If you are running the switch setup utility for the first-time, it starts automatically. If this is not
the first-time configuration, you are required to enter
setup
at the system prompt.
Note
If you do not wish to answer a previously configured question, or if you wish to skip answers to
any questions, press
Enter
. If a default answer is not available (for example, the switch name),
the switch uses what was previously configured and skips to the next question.
Step 5
Enter
yes
to enter setup mode.
This setup utility will guide you through the basic configuration of the system. Setup
configures only enough connectivity for management of the system.
*Note: setup is mainly used for configuring the system initially,
when no configuration is present. So setup always assumes system
defaults and not the current system configuration values.
Press Enter at anytime to skip a dialog. Use ctrl-c at anytime
to skip the remaining dialogs.