Home » HP Manuals » Desktops » HP D530 » Manual Viewer

HP D530 HP Compaq Business Desktop d500 Service Reference Guide, 5th Edition - Page 186

POST Error Messages, Control, Panel, Screen Message, Probable Cause, Recommended Action

UPC - 808736649308

Add to My Manuals
Save this manual to your list of manuals

Page 186 highlights

POST Error Messages POST Error Messages Screen Message 163-Time & Date Not Set 164-Memory Size Error Probable Cause Invalid time or date in configuration memory. RTC (real-time clock) battery may need to be replaced. CMOS jumper may not be properly installed. Memory configuration is incorrect. 183-Invalid Processor Jumper Setting 201-Memory Error System board jumper improperly set. RAM failure. 202-Memory Type Mismatch 207-ECC Corrected Single Bit Errors in Memory Socket(s) y,y Memory modules do not match each other. Single Bit ECC error. 212-Failed Processor Processor has failed to initialize. 213-Incompatible memory Module in memory Socket(s) X,X, X A memory module in memory socket identified in the error message is missing critical SPD information, or is incompatible with the chipset. Recommended Action Set the date and time under Control Panel or in F10 Setup depending on the operating system. If the problem persists, replace the RTC battery. Run Computer Setup (F10 Setup) or Windows utilities. Make sure memory module(s) (if any) are installed properly. If third party memory has been added, test using HP-only memory. Verify proper memory module type. Reset system board jumpers to match processor and bus speeds (select models). Run Computer Setup (F10 Setup) or Windows utilities. Ensure memory and continuity modules are installed correctly. Verify proper memory module type. Remove and replace memory module(s) one at a time to isolate faulty module. Replace the faulty memory module(s). If error persists after replacing memory modules, replace the system board. Replace memory modules with matched sets. Verify proper memory module type. Try another memory socket. Replace memory module if problem persists. Reseat the processor in its socket. If the processor does not respond, replace it. Verify proper memory module type. Try another memory socket. Replace memory with a module conforming to the SPD standard. C-2 336492-005 Service Reference Guide, d500

Section	Page
Contents	5
Installing the Operating System	11
1.0.1 Installing or Upgrading Device Drivers	11
1.0.2 Creating an Emergency Repair Diskette - Windows 2000	11
1.0.3 Using the Emergency Repair Diskette - Windows 2000	11
1.1 Converting to NTFS	12
1.1.1 Windows 2000 Professional	12
1.1.2 Windows XP Home and XP Professional	12
1.2 HP Software	12
Setup Utilities and Diagnostics Features	13
2.1 Power-On Self-Test (POST)	13
2.2 Computer Setup Utilities	14
2.2.1 Using Computer Setup (F10) Utilities	15
2.2.2 Computer Setup Menu	16
2.3 Diagnostics for Windows	25
2.3.1 Detecting Diagnostics for Windows	25
2.3.2 Installing Diagnostics for Windows	25
2.3.3 Using Categories in Diagnostics for Windows	26
2.3.4 Running Diagnostic Tests in Diagnostics for Windows	28
2.4 Configuration Record	29
2.4.1 Installing Configuration Record	29
2.4.2 Running Configuration Record	29
2.5 Remote Diagnostics Enabling Agent	30
2.5.1 Installing or Upgrading Remote Diagnostics Enabling Agent	30
2.5.2 Running the Remote Diagnostics Enabling Agent	30
2.6 Protecting the Software	30
2.7 Restoring the Software	31
Desktop Management	33
3.1 Initial Configuration and Deployment	33
3.2 Remote System Installation	34
3.3 Software Updating and Management	34
3.3.1 HP Client Manager Software	34
3.3.2 Altiris Client Management Solutions	34
3.3.3 System Software Manager	35
3.3.4 Proactive Change Notification (PCN)	35
3.3.5 Subscriber’s Choice	36
3.4 ROM Flash	36
3.4.1 Remote ROM Flash	36
3.4.2 FHPQ Flash	36
3.4.3 FailSafe Boot Block ROM	37
3.4.4 Replicating Your Setup	38
3.4.5 Dual-State Power Button	38
3.4.6 Power Management	39
3.4.7 World Wide Web Site	39
3.4.8 Building Blocks and Partners	39
3.5 Asset Tracking and Security	40
3.5.1 Password Security	43
3.5.2 Establishing a Setup Password Using Computer Setup	43
3.5.3 Establishing a Power-On Password Using Computer Setup	44
3.5.4 DriveLock	46
3.5.5 Smart Cover Sensor	48
3.5.6 Master Boot Record Security	50
3.5.7 Before You Partition or Format the Current Bootable Disk	51
3.5.8 Cable Lock Provision	51
3.5.9 Fingerprint Identification Technology	51
3.6 Fault Notification and Recovery	52
3.6.1 Drive Protection System	52
3.6.2 Surge-Tolerant Power Supply	52
3.6.3 Thermal Sensor	52
Serial and Parallel ATA Drive Guidelines and Features	53
4.1 PATA and SATA Device Information	53
4.2 ATA Cables	53
4.2.1 SATA Data Cable	53
4.2.2 SATA Power Cable	54
4.2.3 PATA Data Cable	54
4.2.4 PATA Power Cable	54
4.2.5 PATA Cable Layout	55
4.3 PATA Drive Installation Guidelines	55
4.3.1 PATA Device Classes	56
4.3.2 PATA Attach Sequence Rules by Class Priority	57
4.3.3 PATA Attach Sequence Worksheet	58
4.3.4 PATA Additional Drive Application Notes	60
4.4 PATA SMART Drives	61
4.5 Drive Capacities	61
4.6 SATA BIOS	61
4.6.1 Legacy Mode	62
4.6.2 Native Mode	62
4.7 Mixed Devices Boot and Drive Letter Ordering	63
Identifying the Chassis, Routine Care, and Disassembly Preparation	65
5.1 Chassis Designations	65
5.1.1 Convertible Minitower (CMT)	65
5.1.2 Small Form Factor (SFF)	66
5.1.3 Ultra-Slim Desktop (USDT)	66
5.2 Electrostatic Discharge Information	67
5.2.1 Generating Static	67
5.2.2 Preventing Electrostatic Damage to Equipment	67
5.2.3 Personal Grounding Methods and Equipment	68
5.2.4 Grounding the Work Area	68
5.2.5 Recommended Materials and Equipment	68
5.3 Routine Care	69
5.3.1 General Cleaning Safety Precautions	69
5.3.2 Cleaning the Computer Case	69
5.3.3 Cleaning the Keyboard	70
5.3.4 Cleaning the Monitor	70
5.3.5 Cleaning the Mouse	70
5.4 Service Considerations	71
5.4.1 Power Supply Fan	71
5.4.2 Tools and Software Requirements	71
5.4.3 Screws	71
5.4.4 Cables and Connectors	72
5.4.5 Hard Drives	72
5.4.6 Lithium Coin Cell Battery	72
Removal and Replacement Procedures- Convertible Minitower (CMT) Chassis	73
6.1 Preparation for Disassembly	73
6.2 Unlocking the Smart Cover Lock	74
6.3 Hood Sensor	75
6.4 External Security Devices	76
6.4.1 Cable Lock	76
6.4.2 Padlock	76
6.5 Computer Access Panel	77
6.6 Front Bezel	78
6.7 Front Drive Bezels	79
6.7.1 5.25\	79
6.7.2 Diskette Drive Bezel or Bezel Blank	80
6.8 Memory	80
6.9 Expansion Cards	81
6.10 PCI Retainer Latch	86
6.11 Drives	88
6.11.1 Drive Positions	89
6.11.2 Hard Drive	90
6.11.3 Optical Drive	92
6.11.4 Diskette Drive	95
6.12 Front I/O Device	96
6.13 Power Switch Assembly	97
6.14 System Board	98
6.15 Battery	99
6.15.1 Type 1 Battery Holder	100
6.15.2 Type 2 Battery Holder	101
6.16 Processor and Heatsink	102
6.16.1 Type 1	102
6.16.2 Type 2	103
6.16.3 Type 3	104
6.17 Speaker	105
6.18 Chassis Fan	106
6.19 Power Supply	107
6.20 Changing from Desktop to Minitower	108
6.21 Changing from Minitower to Desktop	111
Removal and Replacement Procedures- Small Form Factor (SFF) Chassis	115
7.1 Preparation for Disassembly	115
7.2 Unlocking the Smart Cover Lock	116
7.3 Hood Sensor	117
7.4 External Security Devices	118
7.4.1 Cable Lock	118
7.4.2 Padlock	118
7.5 Computer Access Panel	119
7.6 Front Bezel	120
7.7 Front Drive Bezels	121
7.7.1 Diskette Drive Bezel or Bezel Blank	121
7.8 Memory	122
7.9 Expansion Card Cage	123
7.9.1 Riser Card	124
7.9.2 Expansion Card	125
7.9.3 AGP Card	127
7.10 Drives	129
7.10.1 Drive Positions	129
7.10.2 Cable Routing	130
7.10.3 Optical Drive	131
7.10.4 External 3.5-inch Drive	134
7.10.5 Primary Hard Drive	136
7.11 Front I/O Devices	138
7.12 Power Switch Assembly	139
7.13 System Board	140
7.14 Chassis Fan	141
7.15 Battery	142
7.15.1 Type 1 Battery Holder	143
7.15.2 Type 2 Battery Holder	144
7.16 Processor and Heatsink	145
7.17 Speaker	146
7.18 Power Supply	147
Removal and Replacement Procedures- Ultra-Slim Desktop (USDT) Chassis	149
8.1 Preparation for Disassembly	149
8.2 External Security Devices	150
8.2.1 Installing a Cable Lock	150
8.2.2 Installing a Padlock	151
8.3 Computer Access Panel	152
8.3.1 Top Access Panel	152
8.3.2 Bottom Access Panel	153
8.4 Front Bezel	154
8.5 Memory	155
8.6 Expansion Cards	156
8.7 Expansion Card Locking Lever	158
8.8 Drives	159
8.8.1 Hard Drive	159
8.8.2 MultiBay Drive	161
8.9 System Fan	162
8.10 Front Chassis Panel	163
8.11 Front I/O Device	164
8.12 Power Switch Assembly	165
8.13 Processor and Heatsink	166
8.14 Power Supply	167
8.15 Battery	168
8.15.1 Type 1 Battery Holder	169
8.15.2 Type 2 Battery Holder	170
8.16 Drive Cage Assembly	171
8.17 Speaker	172
8.18 Chassis Fan	173
8.19 System Board	174
Connector Pin Assignments	175
Power Cord Set Requirements	183
POST Error Messages	185
Troubleshooting Without Diagnostics	193
System Board and Riser Board Reference Designators	219
Memory	223

Match case Limit results 1 per page

C–2

336492-005

Service Reference Guide, d500

POST Error Messages

163-Time & Date Not

Set

Invalid time or date in

configuration memory.

RTC (real-time clock)

battery may need to be

replaced.

CMOS jumper may not

be properly installed.

Set the date and time under

Control

Panel

or in F10 Setup depending on

the operating system.

If the problem persists, replace the RTC

battery.

164-Memory Size Error

Memory configuration is

incorrect.

Run Computer Setup (F10 Setup) or

Windows utilities.

Make sure memory module(s) (if any) are

installed properly.

If third party memory has been added,

test using HP-only memory.

Verify proper memory module type.

183-Invalid Processor

Jumper Setting

System board jumper

improperly set.

Reset system board jumpers to match

processor and bus speeds (select

models).

201-Memory Error

RAM failure.

Run Computer Setup (F10 Setup) or

Windows utilities.

Ensure memory and continuity modules

are installed correctly.

Verify proper memory module type.

Remove and replace memory module(s)

one at a time to isolate faulty module.

Replace the faulty memory module(s).

If error persists after replacing memory

modules, replace the system board.

202-Memory Type

Mismatch

Memory modules do not

match each other.

Replace memory modules with matched

sets.

207-ECC Corrected

Single Bit Errors in

Memory Socket(s) y,y

Single Bit ECC error.

Verify proper memory module type.

Try another memory socket.

Replace memory module if problem

persists.

212-Failed Processor

Processor has failed to

initialize.

Reseat the processor in its socket.

If the processor does not respond,

replace it.

213-Incompatible

memory Module in

memory Socket(s)

X,X, X

A memory module in

memory socket identified

in the error message is

missing critical SPD

information, or is

incompatible with the

chipset.

Verify proper memory module type.

Try another memory socket.

Replace memory with a module

conforming to the SPD standard.

POST Error Messages

Screen Message

Probable Cause

Recommended Action