Home » HP Manuals » Desktops » HP D530 » Manual Viewer

HP D530 HP Compaq Business Desktop d500 Service Reference Guide, 5th Edition - Page 188

Run Computer Setup F10 Setup., CPU or Chassis

UPC - 808736649308

Add to My Manuals
Save this manual to your list of manuals

Page 188 highlights

POST Error Messages POST Error Messages Screen Message 501-Display Adapter Failure Probable Cause Graphics display controller. 510-Splash Screen image corrupted 511-CPU, CPUA, or CPUB Fan not detected Splash Screen image has errors. Fan is not connected or may have malfunctioned. 512-Chassis, rear chassis, or front chassis fan not detected Fan is not connected, may have malfunctioned. 514-CPU or Chassis Fan not detected. 520-Single Monitor Configuration warning 601-Diskette Controller Error CPU fan is not connected or may have malfunctioned. Single monitor configuration with monitor attached to video port 2. Diskette controller circuitry or floppy drive circuitry incorrect. 602-Diskette Boot Record Error 605-Diskette Drive Type Error Diskette in drive A not bootable. Mismatch in drive type. 610-External Storage Device Failure External tape drive not connected. 611-Primary Floppy Port Address Assignment Conflict Configuration error. Recommended Action Reseat the graphics card (if applicable). Clear CMOS. Verify that the monitor is attached and turned on. Replace the graphics controller. Install latest version of ROMPaq to restore image. Reseat fan cable. Reseat the fan. Replace the fan. Reseat chassis, rear chassis, or front chassis fan cable. Reseat chassis, rear chassis, or front chassis fan. Replace chassis, rear chassis, or front chassis fan. Reseat CPU or chassis fan. Replace CPU or chassis fan. Turn off unit, attach monitor to video port 1, then restart unit. Run Computer Setup (F10 Setup). Check and/or replace cables. Clear CMOS. Replace diskette drive. Replace the system board. Replace the diskette. Run Computer Setup (F10 Setup). Disconnect any other diskette controller devices (tape drives). Clear CMOS. Reinstall tape drive or press F1 and allow system to reconfigure without the drive. Run Computer Setup (F10 Setup). Remove expansion cards. Clear CMOS. C-4 336492-005 Service Reference Guide, d500

Section	Page
Contents	5
Installing the Operating System	11
1.0.1 Installing or Upgrading Device Drivers	11
1.0.2 Creating an Emergency Repair Diskette - Windows 2000	11
1.0.3 Using the Emergency Repair Diskette - Windows 2000	11
1.1 Converting to NTFS	12
1.1.1 Windows 2000 Professional	12
1.1.2 Windows XP Home and XP Professional	12
1.2 HP Software	12
Setup Utilities and Diagnostics Features	13
2.1 Power-On Self-Test (POST)	13
2.2 Computer Setup Utilities	14
2.2.1 Using Computer Setup (F10) Utilities	15
2.2.2 Computer Setup Menu	16
2.3 Diagnostics for Windows	25
2.3.1 Detecting Diagnostics for Windows	25
2.3.2 Installing Diagnostics for Windows	25
2.3.3 Using Categories in Diagnostics for Windows	26
2.3.4 Running Diagnostic Tests in Diagnostics for Windows	28
2.4 Configuration Record	29
2.4.1 Installing Configuration Record	29
2.4.2 Running Configuration Record	29
2.5 Remote Diagnostics Enabling Agent	30
2.5.1 Installing or Upgrading Remote Diagnostics Enabling Agent	30
2.5.2 Running the Remote Diagnostics Enabling Agent	30
2.6 Protecting the Software	30
2.7 Restoring the Software	31
Desktop Management	33
3.1 Initial Configuration and Deployment	33
3.2 Remote System Installation	34
3.3 Software Updating and Management	34
3.3.1 HP Client Manager Software	34
3.3.2 Altiris Client Management Solutions	34
3.3.3 System Software Manager	35
3.3.4 Proactive Change Notification (PCN)	35
3.3.5 Subscriber’s Choice	36
3.4 ROM Flash	36
3.4.1 Remote ROM Flash	36
3.4.2 FHPQ Flash	36
3.4.3 FailSafe Boot Block ROM	37
3.4.4 Replicating Your Setup	38
3.4.5 Dual-State Power Button	38
3.4.6 Power Management	39
3.4.7 World Wide Web Site	39
3.4.8 Building Blocks and Partners	39
3.5 Asset Tracking and Security	40
3.5.1 Password Security	43
3.5.2 Establishing a Setup Password Using Computer Setup	43
3.5.3 Establishing a Power-On Password Using Computer Setup	44
3.5.4 DriveLock	46
3.5.5 Smart Cover Sensor	48
3.5.6 Master Boot Record Security	50
3.5.7 Before You Partition or Format the Current Bootable Disk	51
3.5.8 Cable Lock Provision	51
3.5.9 Fingerprint Identification Technology	51
3.6 Fault Notification and Recovery	52
3.6.1 Drive Protection System	52
3.6.2 Surge-Tolerant Power Supply	52
3.6.3 Thermal Sensor	52
Serial and Parallel ATA Drive Guidelines and Features	53
4.1 PATA and SATA Device Information	53
4.2 ATA Cables	53
4.2.1 SATA Data Cable	53
4.2.2 SATA Power Cable	54
4.2.3 PATA Data Cable	54
4.2.4 PATA Power Cable	54
4.2.5 PATA Cable Layout	55
4.3 PATA Drive Installation Guidelines	55
4.3.1 PATA Device Classes	56
4.3.2 PATA Attach Sequence Rules by Class Priority	57
4.3.3 PATA Attach Sequence Worksheet	58
4.3.4 PATA Additional Drive Application Notes	60
4.4 PATA SMART Drives	61
4.5 Drive Capacities	61
4.6 SATA BIOS	61
4.6.1 Legacy Mode	62
4.6.2 Native Mode	62
4.7 Mixed Devices Boot and Drive Letter Ordering	63
Identifying the Chassis, Routine Care, and Disassembly Preparation	65
5.1 Chassis Designations	65
5.1.1 Convertible Minitower (CMT)	65
5.1.2 Small Form Factor (SFF)	66
5.1.3 Ultra-Slim Desktop (USDT)	66
5.2 Electrostatic Discharge Information	67
5.2.1 Generating Static	67
5.2.2 Preventing Electrostatic Damage to Equipment	67
5.2.3 Personal Grounding Methods and Equipment	68
5.2.4 Grounding the Work Area	68
5.2.5 Recommended Materials and Equipment	68
5.3 Routine Care	69
5.3.1 General Cleaning Safety Precautions	69
5.3.2 Cleaning the Computer Case	69
5.3.3 Cleaning the Keyboard	70
5.3.4 Cleaning the Monitor	70
5.3.5 Cleaning the Mouse	70
5.4 Service Considerations	71
5.4.1 Power Supply Fan	71
5.4.2 Tools and Software Requirements	71
5.4.3 Screws	71
5.4.4 Cables and Connectors	72
5.4.5 Hard Drives	72
5.4.6 Lithium Coin Cell Battery	72
Removal and Replacement Procedures- Convertible Minitower (CMT) Chassis	73
6.1 Preparation for Disassembly	73
6.2 Unlocking the Smart Cover Lock	74
6.3 Hood Sensor	75
6.4 External Security Devices	76
6.4.1 Cable Lock	76
6.4.2 Padlock	76
6.5 Computer Access Panel	77
6.6 Front Bezel	78
6.7 Front Drive Bezels	79
6.7.1 5.25\	79
6.7.2 Diskette Drive Bezel or Bezel Blank	80
6.8 Memory	80
6.9 Expansion Cards	81
6.10 PCI Retainer Latch	86
6.11 Drives	88
6.11.1 Drive Positions	89
6.11.2 Hard Drive	90
6.11.3 Optical Drive	92
6.11.4 Diskette Drive	95
6.12 Front I/O Device	96
6.13 Power Switch Assembly	97
6.14 System Board	98
6.15 Battery	99
6.15.1 Type 1 Battery Holder	100
6.15.2 Type 2 Battery Holder	101
6.16 Processor and Heatsink	102
6.16.1 Type 1	102
6.16.2 Type 2	103
6.16.3 Type 3	104
6.17 Speaker	105
6.18 Chassis Fan	106
6.19 Power Supply	107
6.20 Changing from Desktop to Minitower	108
6.21 Changing from Minitower to Desktop	111
Removal and Replacement Procedures- Small Form Factor (SFF) Chassis	115
7.1 Preparation for Disassembly	115
7.2 Unlocking the Smart Cover Lock	116
7.3 Hood Sensor	117
7.4 External Security Devices	118
7.4.1 Cable Lock	118
7.4.2 Padlock	118
7.5 Computer Access Panel	119
7.6 Front Bezel	120
7.7 Front Drive Bezels	121
7.7.1 Diskette Drive Bezel or Bezel Blank	121
7.8 Memory	122
7.9 Expansion Card Cage	123
7.9.1 Riser Card	124
7.9.2 Expansion Card	125
7.9.3 AGP Card	127
7.10 Drives	129
7.10.1 Drive Positions	129
7.10.2 Cable Routing	130
7.10.3 Optical Drive	131
7.10.4 External 3.5-inch Drive	134
7.10.5 Primary Hard Drive	136
7.11 Front I/O Devices	138
7.12 Power Switch Assembly	139
7.13 System Board	140
7.14 Chassis Fan	141
7.15 Battery	142
7.15.1 Type 1 Battery Holder	143
7.15.2 Type 2 Battery Holder	144
7.16 Processor and Heatsink	145
7.17 Speaker	146
7.18 Power Supply	147
Removal and Replacement Procedures- Ultra-Slim Desktop (USDT) Chassis	149
8.1 Preparation for Disassembly	149
8.2 External Security Devices	150
8.2.1 Installing a Cable Lock	150
8.2.2 Installing a Padlock	151
8.3 Computer Access Panel	152
8.3.1 Top Access Panel	152
8.3.2 Bottom Access Panel	153
8.4 Front Bezel	154
8.5 Memory	155
8.6 Expansion Cards	156
8.7 Expansion Card Locking Lever	158
8.8 Drives	159
8.8.1 Hard Drive	159
8.8.2 MultiBay Drive	161
8.9 System Fan	162
8.10 Front Chassis Panel	163
8.11 Front I/O Device	164
8.12 Power Switch Assembly	165
8.13 Processor and Heatsink	166
8.14 Power Supply	167
8.15 Battery	168
8.15.1 Type 1 Battery Holder	169
8.15.2 Type 2 Battery Holder	170
8.16 Drive Cage Assembly	171
8.17 Speaker	172
8.18 Chassis Fan	173
8.19 System Board	174
Connector Pin Assignments	175
Power Cord Set Requirements	183
POST Error Messages	185
Troubleshooting Without Diagnostics	193
System Board and Riser Board Reference Designators	219
Memory	223

Match case Limit results 1 per page

C–4

336492-005

Service Reference Guide, d500

POST Error Messages

501-Display Adapter

Failure

Graphics display

controller.

Reseat the graphics card (if applicable).

Clear CMOS.

Verify that the monitor is attached and

turned on.

Replace the graphics controller.

510-Splash Screen

image corrupted

Splash Screen image has

errors.

Install latest version of ROMPaq to

restore image.

511-CPU, CPUA, or

CPUB Fan not detected

Fan is not connected or

may have malfunctioned.

Reseat fan cable.

Reseat the fan.

Replace the fan.

512-Chassis, rear

chassis, or front chassis

fan not detected

Fan is not connected,

may have malfunctioned.

Reseat chassis, rear chassis, or front

chassis fan cable.

Reseat chassis, rear chassis, or front

chassis fan.

Replace chassis, rear chassis, or front

chassis fan.

514-CPU or Chassis

Fan not detected.

CPU fan is not connected

or may have

malfunctioned.

Reseat CPU or chassis fan.

Replace CPU or chassis fan.

520-Single Monitor

Configuration warning

Single monitor

configuration with

monitor attached to video

port 2.

Turn off unit, attach monitor to video port

1, then restart unit.

601-Diskette Controller

Error

Diskette controller

circuitry or floppy drive

circuitry incorrect.

Run Computer Setup (F10 Setup).

Check and/or replace cables.

Clear CMOS.

Replace diskette drive.

Replace the system board.

602-Diskette Boot

Record Error

Diskette in drive A not

bootable.

Replace the diskette.

605-Diskette Drive Type

Error

Mismatch in drive type.

Run Computer Setup (F10 Setup).

Disconnect any other diskette controller

devices (tape drives).

Clear CMOS.

610-External Storage

Device Failure

External tape drive not

connected.

Reinstall tape drive or press

and

allow system to reconfigure without the

drive.

611-Primary Floppy Port

Address Assignment

Conflict

Configuration error.

Run Computer Setup (F10 Setup).

Remove expansion cards.

Clear CMOS.

POST Error Messages

Screen Message

Probable Cause

Recommended Action