LG 42CQ610H Setup Guide - Page 25

Installer Menu (Cont.) 079 - UPN MSB-1 (UPN Most Significant Byte-1) User programmable number, most significant byte-1 readable by MPI command. Note: Not linked to serial number. 080 - UPN MSB-2 (UPN Most Significant Byte-2) User programmable number, most significant byte-2 readable by MPI command. Note: Not linked to serial number. 081 - UPN LSB (UPN Least Significant Byte) User programmable number, least significant byte readable by MPI command. Note: Not linked to serial number. 082 - CHKSM ERROR (Checksum Error) Enforces rigid MPI checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on MPI async port). SPI is always checked. 083 - HANDSHK TIME (Handshake Time) Adds an additional delay to the handshake time which is 64 msec, thus relaxing MPI timing requirements to be compatible with PCbased Windows controlled systems. Range is 0 - 5. (Timeout = 25.5MS + [25.5 MS* Handshake time].) 084 - PERMANENT BLK (Permanent Block) Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes. 087 - REAR RGB EN. (Rear RGB Enable) Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 1 to enable RGB input. Set to 17 to initiate a onetime automatic configuration after an AC power cycle; otherwise, automatic adjustment will be performed each time the RGB input is accessed. 088 - EN NOISE MUTE (Enable Noise Mute) If set to 1, audio mutes when no signal is present. 096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up. • Set to 0 for Set By System. • Set to 1 for 4:3. • Set to 2 for 16:9 (default). • Set to 3 for Just Scan. • Set to 4 for Zoom. Note: This item is not available in the Installer Menu unless item 106 ASP RATIO LOCK is set to 0. 098 - PRO:CENTRIC Selects the Pro:Centric Application Mode. Set to 0 (default) to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for GEM (Java Application) Mode. Note: This item is not available in the Installer Menu when item 119 DATA CHANNEL is set to 0. 099 - BACK LIGHTING Sets the TV screen brightness at power up. Default setting is 255. • 1 - 100 Static Back Lighting (1 = Dimmest picture, 100 = Brightest picture) • 101 - 200 Dynamic Back Lighting (101 = Dimmest picture, 200 = Brightest picture) The TV automatically controls back lighting depending upon the picture level of the current program. • 201 Automatic Static Back Lighting The TV automatically controls back lighting depending upon external spectral sensitivity. • 202 Automatic Dynamic Back Lighting The TV automatically controls back lighting depending upon external spectral sensitivity and the picture level of the current program. • If set to 255, back lighting is controlled via the Picture settings in the TV setup menus. 090 - KEY LOCK If set to 1, front keyboard Channel, Volume, and Caption buttons are disabled, Power button remains enabled. If set to 0, Channel, Volume, Caption, and Power buttons are all enabled. 091 - YPrPb2 EN. (HDMI2 Enable) Set to 1 to enable display panel HDMI 2 input. Set to 0 to disable display panel HDMI 2 input. 094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable SAP feature on Function menu, if Function Menu is available (i.e., the TV is not in Pass-through Mode). Set to 0 to disable SAP feature on Function Menu, if Function Menu is available. 102 - ATSC BAND Sets up TV to receive different types of incoming signals: 0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC. 103 - ATSC TUNE MODE Sets ATSC tuning mode: Default set to 1 for Physical Channel scan. Set to 0 for Virtual Channel scan. 104 - START MINOR CHANNEL Sets Minor Start Channel number at power up. 0 = NTSC. If not 0, number selected is the digital channel's Minor Start Channel number. Note: This item is not available in the Installer Menu when item 004 STRT CHANNEL is set to 0 or 255. 206-4207 25