Home » Lenovo Manuals » Desktops » Lenovo ThinkCentre M50 » Manual Viewer

Lenovo ThinkCentre M50 Hardware Maintenance Manual (HMM) - Page 60

Connecting, drive, Parallel

Get Lenovo ThinkCentre M50 PDF manuals and user guides

View all Lenovo ThinkCentre M50 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Note: This illustration shows a CD drive installation. The hard disk drive and diskette drive is installed in the same manner except that the front bezel is not in place. 3. If the front bezel was removed, replace it by aligning the four plastic tabs and pressing the bezel into position. 4. Go to "Connecting the drive." Connecting the drive Each drive requires two cables; a power cable from the power supply and a signal cable that connects the drive to the system board. See "Identifying parts on the system board (all machine types)" on page 38. There are two types of hard disk drives; parallel ATA and serial ATA. Each one is connected to a different location on the system board. See "Parallel ATA hard disk drive" and "Serial ATA hard disk drive" on page 55. Other drives, such as a CD drive, connect to either the primary or secondary PATA connector. The diskette drive connects to the diskette drive connector. Parallel ATA hard disk drive 54 Hardware Maintenance Manual

Section	Page
Contents	5
Chapter 1. About this manual	7
Important Safety Information	7
Chapter 2. General information	9
Features	9
Physical specifications	11
Types 8185, 8186, 8192, 8413, and 8430	12
Types 8128, 8187, 8188, 8193, 8414, and 8431	13
Types 8189, 8190, 8194, 8195, 8415, 8432, and 8433	14
Types 8196 and 8197	15
Chapter 3. General Checkout	17
Chapter 4. IBM Enhanced Diagnostics	21
Diagnostics program download	21
Navigating through the diagnostics programs	21
Running diagnostics tests	21
Test selection	22
Test results	22
Fixed disk advanced test (FDAT)	22
Quick and Full erase - hard drive	24
Viewing the test log	24
Chapter 5. IBM Setup Utility program	25
Starting the IBM Setup Utility program	25
Viewing and changing settings	25
Exiting from the IBM Setup Utility program	26
Using passwords	26
User password	26
Administrator password	26
Setting, changing, and deleting a password	26
Using Security Profile by Device	27
Using IDE Drives Setup	27
Selecting a startup device	28
Selecting a temporary startup device	28
Changing the startup device sequence	28
Chapter 6. Replacing FRUs	29
Locating connectors on the front	29
Types 8185, 8186, 8192, 8413, and 8430	29
Types 8128, 8187, 8188, 8193, 8414, and 8431	29
Types 8189, 8190, 8194, 8195, 8415, 8432, and 8433	31
Types 8196 and 8197	31
Locating the connectors on the rear	33
Types 8185, 8186, 8192, 8413, and 8430	33
Types 8128, 8187, 8188, 8193, 8414, and 8431	33
Types 8189, 8190, 8194, 8195, 8415, 8432, and 8433	35
Types 8196 and 8197	35
Removing the cover	36
Types 8185, 8186, 8192, 8413, and 8430	36
Types 8128, 8187, 8188, 8193, 8414, and 8431	37
Types 8189, 8190, 8194, 8195, 8415, 8432, and 8433	37
Types 8196 and 8197	38
Locating components	40
Types 8185, 8186, 8192, 8413, and 8430	40
Types 8128, 8187, 8188, 8193, 8414, and 8431	41
Types 8189, 8190, 8194, 8195, 8415, 8432, and 8433	42
Types 8196 and 8197	43
Identifying parts on the system board (all machine types)	44
Replacing memory (all machine types)	44
Replacing adapters	45
Types 8185, 8186, 8192, 8413, and 8430	45
Types 8128, 8187, 8188, 8193, 8414, and 8431	47
Types 8189, 8190, 8194, 8195, 8415, 8432, and 8433	48
Types 8196 and 8197	48
Replacing internal drives	49
Types 8185, 8186, 8192, 8413, and 8430	49
Drive bay information	49
Removing a drive	50
Installing a drive	51
Types 8128, 8187, 8188, 8193, 8414, and 8431	51
Drive bay information	51
Removing a drive	52
Installing a drive	53
Types 8189, 8190, 8194, 8195, 8415, 8432, and 8433	54
Drive bay information	54
Removing the drive	54
Installing a drive	55
Types 8196 and 8197	57
Drive bay information	57
Removing a drive	57
Installing a drive	59
Connecting the drive	60
Parallel ATA hard disk drive	60
Serial ATA hard disk drive	61
CD drive, DVD drive, CD/RW drive, or DVD/CD/RW combo drive	61
Diskette drive	61
Replacing the battery (all machine types)	62
Replacing the power supply	63
Types 8185, 8186, 8192, 8413, and 8430	63
Types 8128, 8187, 8188, 8193, 8414, and 8431	63
Types 8189, 8190, 8194, 8195, 8196, 8197, 8415, 8432, and 8433	64
Replacing a microprocessor (all machine types)	65
Replacing the system board (all machine types)	67
Replacing the cover and connecting the cables	69
Types 8185, 8186, 8192, 8413, and 8430	69
Types 8128, 8187, 8188, 8193, 8414, and 8431	70
Types 8189, 8190, 8194, 8195, 8415, 8432, and 8433	71
Types 8196 and 8197	72
Chapter 7. Symptom-to-FRU Index	75
Hard disk drive boot error	75
Power Supply Errors	76
Diagnostic error codes	76
Beep symptoms	95
No-beep symptoms	97
POST error codes	98
Miscellaneous error messages	113
Undetermined problems	115
Power supply connectors	116
Connector P1	116
Connector P2, P3, P4, and P7	116
Connector P5 (Diskette drive)	116
Connector P6	116
Connector P8 (Serial ATA)	116
Chapter 8. Additional Service Information	117
Security features	117
Passwords	117
Power-on password	117
Removing a power-on password	117
Administrator password	117
Administrator password control	118
Operating system password	118
Vital product data	118
BIOS levels	118
Erasing a lost or forgotten password (clearing CMOS)	119
Flash update procedures	119
Updating (flashing) BIOS from a diskette or CD-ROM	119
Updating (flashing) BIOS from your operating system	119
Recovering from a POST/BIOS update failure	120
Power management	121
Automatic configuration and power interface (ACPI) BIOS	121
Advanced Power Management	121
Automatic Hardware Power Management features	121
Setting Automatic Hardware Power Management features	121
Automatic Power-On features	122
Product Recovery Program	123
Chapter 9. Parts listing	125
Type 8128	125
Type 8185	127
Type 8186	136
Type 8187	140
Type 8188	155
Type 8189	164
Type 8190	178
Type 8192	184
Type 8193	186
Type 8194	194
Type 8195	208
Type 8196	217
Type 8197	221
Type 8413	224
Type 8414	229
Type 8415	235
Type 8430	238
Type 8431	242
Type 8432	247
Type 8433	250
Chapter 10. Related service information	253
Safety information	253
General safety	253
Electrical safety	254
Safety inspection guide	255
Handling electrostatic discharge-sensitive devices	256
Grounding requirements	257
Safety notices (multi-lingual translations)	257
Send us your comments!	286
Problem determination tips	287
Notices	287

Match case Limit results 1 per page

Note:

This

illustration

shows

drive

installation.

The

hard

disk

drive

and

diskette

drive

installed

the

same

manner

except

that

the

front

bezel

not

place.

the

front

bezel

was

removed,

replace

aligning

the

four

plastic

tabs

and

pressing

the

bezel

into

position.

“Connecting

the

drive.”

Connecting

the

drive

Each

drive

requires

two

cables;

power

cable

from

the

power

supply

and

signal

cable

that

connects

the

drive

the

system

board.

See

“Identifying

parts

the

system

board

(all

machine

types)”

page

38.

There

are

two

types

hard

disk

drives;

parallel

ATA

and

serial

ATA.

Each

one

connected

different

location

the

system

board.

See

“Parallel

ATA

hard

disk

drive”

and

“Serial

ATA

hard

disk

drive”

page

55.

Other

drives,

such

drive,

connect

either

the

primary

secondary

PATA

connector.

The

diskette

drive

connects

the

diskette

drive

connector.

Parallel

ATA

hard

disk

drive

Hardware

Maintenance

Manual