Nokia IP390 Installation Guide - Page 52

Insert a blank bezel into the front panel slot formerly occupied by the NIC and push

Get Nokia IP390 - Security Appliance PDF manuals and user guides View all Nokia IP390 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

5 Installing and Replacing Network Interface Cards 5. From above the chassis tray assembly, remove the NIC retaining screws from the back of the NIC. 00530 6. Remove the NIC by lifting the back of the NIC (as close as possible to the connector locations) away from the chassis tray assembly and pulling the NIC gently away from the front panel. 00533a 7. Insert the new NIC or blank bezel. „ If you are removing a NIC without installing another NIC: a. Insert a blank bezel into the front panel slot formerly occupied by the NIC and push it gently into place. Make sure that the bezel is completely seated into the front panel and that the screw holes on the bottom of the bezel align with those in the front panel. Note To reduce electromagnetic interference (EMI), a blank bezel needs to be installed in the place of any NIC you have removed. b. Proceed to step 9. 52 IP390 Security Platform Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
5
Installing and Replacing Network Interface Cards
52
IP390 Security Platform Installation Guide
5.
From above the chassis tray assembly, remove the NIC retaining screws from the back of the
NIC.
6.
Remove the NIC by lifting the back of the NIC (as close as possible to the connector
locations) away from the chassis tray assembly and pulling the NIC gently away from the
front panel.
7.
Insert the new NIC or blank bezel.
If you are removing a NIC without installing another NIC:
a.
Insert a blank bezel into the front panel slot formerly occupied by the NIC and push it
gently into place.
Make sure that the bezel is completely seated into the front panel and that the screw holes
on the bottom of the bezel align with those in the front panel.
Note
To reduce electromagnetic interference (EMI), a blank bezel needs to be installed in the
place of any NIC you have removed.
b.
Proceed to
step 9
.
00530
00533a