Oki B6300 B6200/6300 Technical Reference/User's Guide - Page 93

Troubleshooting - drum

Page 93 highlights

5 5.1 Troubleshooting When Paper Jams CAUTION • When removing jammed paper, make sure that no pieces of torn paper are left in the machine. A piece of paper remaining in the machine can cause fire. If a sheet of paper is wrapped around the heat roller, or when clearing a jammed paper that is difficult or impossible to see, do not try to remove it by yourself. Doing so can cause injuries or burns. Switch off the machine immediately, and contact your dealers or our Printer Support Desk. Following the message on the control panel, open the cover and remove the jammed paper. If paper is torn, check for any remaining torn pieces of paper. Cover D (offset catch tray) Cover B *1 Open Cover B (For B6300, raise the lever as shown in the diagram and open the cover B (1)). After opening cover B, hold the part marked with and open the cover of the fuser unit (2) and remove any jammed paper. Cover A When the optional offset catch tray is installed, fold the tray first before opening cover A. When a message to remove the drum/toner cartridge is displayed: P. 90 Paper tray Pull out the tray and follow the procedure to remove paper P. 90 CAUTION • The fuser unit is hot. You may get burnt if you touch it directly. Cover C *1 (duplex unit) *1: Remove the rear tray when opening the back cover. Push up the lever shown in the diagram to open the cover. 5.1 When Paper Jams 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163

5.1 When Paper Jams
89
5
Troubleshooting
5.1
When Paper Jams
CAUTION
When removing jammed paper, make sure that no pieces of torn paper are left in the
machine. A piece of paper remaining in the machine can cause fire. If a sheet of paper is
wrapped around the heat roller, or when clearing a jammed paper that is difficult or
impossible to see, do not try to remove it by yourself. Doing so can cause injuries or
burns. Switch off the machine immediately, and contact your dealers or our Printer
Support Desk.
Following the message on the control panel, open the cover and remove the jammed paper.
If paper is torn, check for any remaining torn pieces of paper.
CAUTION
The fuser unit is hot. You may
get burnt if you touch it directly.
*1: Remove the rear tray when
opening the back cover.
Push up the lever shown
in the diagram to open the
cover.
Pull out the tray and follow
the procedure to remove
paper
P. 90
When a message to remove the
drum/toner cartridge is displayed:
P. 90
When the optional offset catch tray
is installed, fold the tray first before
opening cover A.
Cover D
(offset catch tray)
Cover C
*1 (duplex unit)
Paper tray
Cover B
*1
Cover A
Open Cover B (For B6300, raise the
lever as shown in the diagram and
open the cover B (1)). After opening
cover B, hold the part marked with
and open the cover of the fuser unit
(2) and remove any jammed paper.