Pioneer VSX-1021-K Owner's Manual - Page 62

11 The Advanced MCACC menu - The calibration corresponding to the currently selected MCACC preset will be used when EQ ON is selected. To use another MCACC preset, press MCACC to select the MCACC memory you want to store. - After auto calibration with EQ Type : SYMMETRY (Full Auto MCACC, etc.), the graph for the inferred reverb characteristics can be displayed by selecting Reverb View. To display the actually measured reverb characteristics after EQ calibration, measure with EQ ON. When the reverb measurement is finished, you can select Reverb View to see the results on-screen. See Professional Calibration EQ graphical output on page 74 for troubleshooting information. 4 If you selected 'Reverb View', you can check the reverb characteristics for each channel. Press RETURN when you're done. The reverb characteristics are displayed when the Full Auto MCACC or Reverb Measurement measurements are conducted. Use k/l to select the channel, frequency and calibration setting you want to check. Use i/j to go back and forth between the three. The reverb characteristics graph before and after EQ calibration can be displayed by selecting Calibration : Before / After. Note that the markers on the vertical axis indicate decibels in 2 dB steps. 5 If 'Advanced EQ Setup' is selected, select the MCACC memory to be stored, then enter the desired time setting for calibration, and then select START. ! To specify the place where the MCACC memory is to be stored, press MCACC to select the MCACC memory you want to store. Based on the reverb measurement above, you can choose the time period that will be used for 62 En the final frequency adjustment and calibration. Even though you can make this setting without reverb measurement, it is best to use the measurement results as a reference for your time setting. For an optimal system calibration based on the direct sound coming from the speakers, we recommend using the 30-50ms setting. Use k/l to select the setting. Use i/j to switch between them. Select the setting from the following time periods (in milliseconds): 0-20ms, 10-30ms, 20-40ms, 30-50ms, 40-60ms, 50-70ms and 60-80ms. This setting will be applied to all channels during calibration. When you're finished, select START. It will take about 2 to 4 minutes for the calibration to finish. After the Acoustic Calibration Equalization is set, you are given the option to check the settings on-screen. Checking MCACC Data At the procedure of Automatically conducting optimum sound tuning (Full Auto MCACC) on page 24 , the procedure of Automatic MCACC (Expert) on page 58 or after fine-adjusting at Manual MCACC setup on page 60 , you can check your calibrated settings using the GUI screen. 1 Press on the remote control, then press HOME MENU. A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the screens and select menu items. Press RETURN to exit the current menu. 2 Select 'MCACC Data Check' from the Home Menu. 3 Select the setting you want to check. ! Speaker Setting - Used to check the settings of the speaker systems. See Speaker Setting on page 62 for more on this. ! Channel Level - Used to check the output level of the different speakers. See Channel Level on page 62 for more on this. ! Speaker Distance - Used to check the distance to the different speakers. See Speaker Distance on page 62 for more on this. ! Standing Wave - Used to check the standing wave control filter settings. See Standing Wave on page 63 for more on this. ! Acoustic Cal EQ - Used to check the calibration values of the listening environment's frequency response. See Acoustic Cal EQ on page 63 for more on this. 4 Press RETURN to go back to the MCACC Data Check menu, repeating steps 2 and 3 to check other settings. 5 When you're finished, press RETURN. You will return to the Home Menu. Speaker Setting Use this to display the speaker size and number of speakers. See Speaker Setting on page 64 for more on this. 1 Select 'Speaker Setting' from the MCACC Data Check menu. 2 Select the channel you want to check. Use i/j to select the channel. The corresponding channel on the layout diagram is highlighted. Channel Level Use this to display the level of the various channels. See Channel Level on page 65 for more on this. 1 Select 'Channel Level' from the MCACC Data Check menu. 2 When 'MCACC' is highlighted, use k/l to select the MCACC preset you want to check. The level of the various channels set at the selected MCACC preset is displayed. '---' is displayed for channels that are not connected. Speaker Distance Use this to display the distance from the different channels to the listening position. See Speaker Distance on page 65 for more on this. 1 Select 'Speaker Distance' from the MCACC Data Check menu. 2 When 'MCACC' is highlighted, use k/l to select the MCACC preset you want to check. The distance from the various channels set at the selected MCACC preset is displayed. '---' is displayed for channels that are not connected.