Sharp AR-M205 AR-M160 AR-M205 Operation Manual - Page 14

Power On And Off

Get Sharp AR-M205 PDF manuals and user guides View all Sharp AR-M205 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

POWER ON AND OFF The power switch is located on the left side of the machine. POWER ON POWER OFF Turn the power switch to the "ON" position It will take about 45 seconds for the machine to warm up. While the machine is warming up, the POWER SAVE indicator will blink. (The POWER SAVE indicator will go off when the machine is ready to copy.) However, you can make desired settings and press the [START] key ( ) during warm-up. Copying will start after warm-up. Make sure that the machine is not in operation and then turn the power switch to the "OFF" position. If the power switch is turned off while the machine is in operation, a misfeed may occur and the job that was in progress will be canceled. Check the following to make sure the machine is not in operation: • The START indicator is lit. (Initial state) • The POWER SAVE indicator is lit. ("Preheat mode" or "Auto power shut-off" mode) Note • "Auto clear" is initially set to return the copy settings to the initial settings when the [CLEAR ALL] key ( ) is pressed, and after one minute elapses after a copy job is finished. When "Auto clear" operates, all previous settings are cleared. The setting for "Auto clear" can be changed in the user programs. (p.44) • The machine is initially set to automatically enter power save mode if not used for copying, printing, or scanning for a preset period of time. This setting can be changed in the user programs. (p.44) Power Save Modes The machine has two power save modes to reduce overall power consumption thereby reducing the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are "Preheat mode" and "Auto power shut-off mode". Preheat mode This function automatically switches the machine to a low power consumption state if the set duration of time elapses without the machine being used when the power is on. The POWER SAVE indicator lights up, however, the keys on the operation panel can be used. Normal operation automatically resumes when a key on the operation panel is pressed, an original is placed, a print job is received, or scanning is begun from a computer. Auto power shut-off mode This function automatically switches the machine to a state that consumes even less power than preheat mode if the set duration of time elapses without the machine being used when the power is on. All lights except the POWER SAVE indicator and ON LINE indicator go off. To resume normal operation, press the [START] key ( ). Normal operation also resumes automatically when a print job is received or scanning is begun from a computer. While in auto power shut-off mode, no keys (except the [START] key ( )) can be used. Note The preheat activation time and the "Auto power shut-off timer" can be changed using user programs. It is suggested that you set times that are appropriate for your usage of the machine. (p.44) Initial settings The machine assumes the initial settings when it is first turned on, when the [CLEAR ALL] key ( ) is pressed, and approximately one minute after the last copy is made in any mode. Copy ratio: 100%, Exposure: Automatic Copy quantity: 0, All special copier modes: Off Auto paper selection: On, Paper feed station: The tray selected in the "Default tray setting" in the user programs.(p.46) 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
12
POWER ON AND OFF
The power switch is located on the left side of the machine.
POWER ON
Turn the power switch to the "ON"
position
It will take about 45
seconds for the machine
to warm up. While the
machine is warming up,
the POWER SAVE
indicator will blink. (The
POWER SAVE indicator
will go off when the
machine is ready to
copy.)
However, you can make desired settings and press
the [START] key (
) during warm-up. Copying will
start after warm-up.
POWER OFF
Make sure that the machine is not in
operation and then turn the power switch
to the "OFF" position.
If the power switch is
turned off while the
machine is in operation,
a misfeed may occur and
the job that was in
progress will be
canceled.
Check the following to make sure the machine is not in
operation:
•
The START indicator is lit. (Initial state)
•
The POWER SAVE indicator is lit. ("Preheat mode"
or "Auto power shut-off" mode)
Power Save Modes
Preheat mode
This function automatically switches the machine to a low power consumption state if the set duration of time
elapses without the machine being used when the power is on. The POWER SAVE indicator lights up, however, the
keys on the operation panel can be used. Normal operation automatically resumes when a key on the operation
panel is pressed, an original is placed, a print job is received, or scanning is begun from a computer.
Auto power shut-off mode
This function automatically switches the machine to a state that consumes even less power than preheat mode if the
set duration of time elapses without the machine being used when the power is on. All lights except the POWER
SAVE indicator and ON LINE indicator go off. To resume normal operation, press the [START] key (
). Normal
operation also resumes automatically when a print job is received or scanning is begun from a computer. While in
auto power shut-off mode, no keys (except the [START] key (
)) can be used.
•
"Auto clear" is initially set to return the copy settings to the initial settings when the [CLEAR ALL] key (
) is
pressed, and after one minute elapses after a copy job is finished. When "Auto clear" operates, all previous
settings are cleared. The setting for "Auto clear" can be changed in the user programs. (p.44)
•
The machine is initially set to automatically enter power save mode if not used for copying, printing, or scanning
for a preset period of time. This setting can be changed in the user programs. (p.44)
The machine has two power save modes to reduce overall power consumption thereby
reducing the cost of operation. In addition, these modes conserve natural resources and help
reduce environmental pollution. The two power save modes are "Preheat mode" and "Auto
power shut-off mode".
The preheat activation time and the "Auto power shut-off timer" can be changed using user programs. It is
suggested that you set times that are appropriate for your usage of the machine. (p.44)
Note
Note
Initial settings
The machine assumes the initial settings when it is first turned on, when the [CLEAR ALL] key (
) is pressed,
and approximately one minute after the last copy is made in any mode.
Copy ratio
: 100%,
Exposure
: Automatic
Copy quantity
: 0,
All special copier modes
: Off
Auto paper selection
: On,
Paper feed station
: The tray selected in the "Default tray setting" in the user programs.(p.46)