TP-Link TD-W8970 TD-W8970 V1 User Guide - Page 75

RIP Settings, Destination IPv6 Address

Get TP-Link TD-W8970 PDF manuals and user guides View all TP-Link TD-W8970 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

TD-W8970 300Mbps Wireless N Gigabit ADSL2+ Modem Router User Guide To add a new entry, follow the instructions below. 1. Click the Add New button in Figure 4-55, and you will see the screen as shown in Figure 4-56. Figure 4-56 2. Enter the following data: ¾ Destination IPv6 Address: The Destination IPv6 Address is the address of the network or host that you want to assign to a static route. ¾ Prefix Length: The prefix length of the destination IPv6 address. ¾ Gateway: Here you should type the IPv6 Gateway address correctly, and the option for Interface will adopt the default IPv6 Gateway address for the IPv6 Static Route. ¾ Interface: Select the Interface name from the drop-down list, or else, the default Interface will be adopted for the IPv6 Static Route. ¾ Status: Select Enabled or Disabled from the drop-down list. 3. Click Save to save your settings. To modify or delete an existing entry: 1. Find the desired entry in the table. 2. Click Edit as desired on the Edit column. Click the Enable/ Disabled Selected button to make selected entries enabled/ disabled. Click the Delete Selected button to delete selected entries. 4.9.4 RIP Settings Choose "Route Settings"Æ"RIP Settings", you can see the RIP (Routing Information Protocol) screen which allows you to configure the RIP. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
TD-W8970
300Mbps Wireless N Gigabit ADSL2+ Modem Router User Guide
66
To add a new entry, follow the instructions below.
1.
Click the
Add New
button in Figure 4-55, and you will see the screen as shown in Figure
4-56.
Figure 4-56
2.
Enter the following data:
¾
Destination IPv6 Address:
The
Destination IPv6 Address
is the address of the network or
host that you want to assign to a static route.
¾
Prefix Length:
The prefix length of the destination IPv6 address.
¾
Gateway:
Here you should type the IPv6 Gateway address correctly, and the option for
Interface
will adopt the default IPv6 Gateway address for the IPv6 Static Route.
¾
Interface:
Select the Interface name from the drop-down list, or else, the default Interface will
be adopted for the IPv6 Static Route.
¾
Status:
Select
Enabled
or
Disabled
from the drop-down list
.
3.
Click
Save
to save your settings.
To modify or delete an existing entry:
1.
Find the desired entry in the table.
2.
Click
Edit
as desired on the
Edit
column.
Click the
Enable/ Disabled Selected
button to make selected entries enabled/ disabled.
Click the
Delete Selected
button to delete selected entries.
4.9.4 RIP Settings
Choose “
Route Settings
”
Æ
“
RIP Settings
”, you can see the RIP (Routing Information Protocol)
screen which allows you to configure the RIP.