Home » Uniden Manuals » Electronics Accessories » Uniden BCT15 » Manual Viewer

Uniden BCT15 English Owners Manual - Page 88

Setting Site Frequencies, Setting Site Modulation, Edit Site, Set Startup Key, Program System

Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

Edit Site F Select a Site F Set Startup Key F Select a startup key from [0] to [9] or select "." for no startup key. Notes: • To unlock the system at startup, press and hold the selected startup key while you turn on the scanner. • The system Quick Key is also enabled. • If you press a different key at startup, the system is locked out. • If you do not assign the system a startup key, the system is not affected by any key press during startup. Setting Site Frequencies MESL [MENU] Program System F Select a trunked system F Edit Site F Select the site F Set Frequencies F New Frequency (or select an existing frequency) F Input a system frequency using the number keys and [.No] key, then press F. If you are entering frequencies for an LTR or EDACS system, the scanner will also prompt you to enter the LCN for the frequency you just entered. LCN's (logical channel numbers) are provided from the same source where you got the other system information. To enter additional frequencies, press [MENU], then to select New Frequency. Then repeat the above. Note: If you select Control Channel Only mode (see "Setting Control-Channel Only (Motorola Systems Only)" on Page 91), you only need to enter the frequency(s) that can be assigned as the control channel. Most frequency lists usually indicate which of the frequencies are the control channel frequencies. Otherwise, you must enter all of the frequencies. Setting Site Modulation ML [MENU] Program System F Select a trunked system F Edit Site F 88

Section	Page
Table of Contents	4
The FCC Wants You to Know	10
Scanning Legally	10
Introduction	12
Feature Highlights	13
General	13
Trunk Tracking	15
Searches and Scanning	16
GPS	17
Weather	17
Memory Storage Limits	18
Search Lockout Limits	18
About This Manual	18
How the Scanner’s Controls Are Represented in This Manual	18
A Short User’s Guide to Assist the First-Time Scanner Enthusiast	20
Understanding Scanning and the BCT15	22
Understanding the Scanner’s Memory	22
Understanding Quick Keys	22
What is Scanning?	23
What is Searching?	23
What is CTCSS/DCS?	23
Conventional Scanning	24
Simplex Operation	24
Repeater Operation	25
What is Trunk Tracking?	25
Trunked Scanning	26
Startup Configuration	26
Multi-Site Trunking	27
Types of Trunking Systems	27
Motorola Trunking	27
EDACS Trunking	28
LTR Trunking	29
Where To Get More Information	30
Information On The Internet	30
Included With Your Scanner	31
Setting Up Your Scanner	32
Power Related Issues	32
When you turn off the scanner using the power switch, the scanner remembers the last settings and mode. When you turn power back on, it resumes the previous mode.	33
Base Station	33
Setting Up an Audio Recording Device or Computer Recording	34
Vehicle Installation	35
Mounting Using the Bracket	35
Mounting Using the Optional DIN-E Sleeve	36
Removing the Scanner from the DIN-E Sleeve	37
Mounting Using ISO Technique	38
Removing the Display Sticker	39
Connecting an Optional Antenna	39
Connecting an Earphone/Headphone	39
Connecting an Extension Speaker	40
Controls, Keys, and Functions	41
Controls, Keys, and Functions	42
A Look at The LCD Display	48
Tones	50
General Tones	50
Weather Alert Tones	50
Menu Mode Tones	50
Scanner Alert Tones	50
Operation	51
Turning On the Scanner and Setting the Squelch	51
Setting the Display Backlight	51
Setting Alert Mute	51
Temporary Alert Mute	51
Continuous Alert Mute	51
Entering Text Within A Menu Option	52
Startup Key Operation	52
Conventional	52
Trunked	52
Service Range	52
Custom Range	53
Scanning Systems	53
Selecting Systems to Scan	54
Selecting System Channel Groups	54
Locking/Unlocking Systems	54
Locking/Unlocking Channels	55
ID Scan/ID Search Mode	55
Holding On a System	55
Holding On a Channel	56
Quickly Storing an ID During ID Search	56
Quick-Storing Channels or Talk Group ID’s (TGID)	56
Trunking Activity Indicators	57
Toggling the Display Mode	57
Introduction to BearTracker Operation	58
Using BearTracker Scanning	58
The BearTracker Scanning Icons	59
Using the BearTracker Warning System	59
Using the Menu	60
General Operations	60
Display Format	61
Editing a Name	61
Editing A Frequency	62
First and Second Menu Levels	62
Programming General Settings	64
Setting and Using the Display Backlight	64
Setting the Dimmer	64
Adjusting the Key Beep	65
Setting the Audio AGC	65
Setting the Display Orientation	65
Adjusting the Display Contrast	66
Setting the GPS Format	66
Setting the Serial Port Speed	67
Displaying Scanner Information	67
Viewing Memory Used	67
Setting the BearTracker Options	67
Set Hold Time	67
Set Delay Time	68
Set Attenuator	68
Set Alert Level	68
Set Alert Tone	69
Set Record	69
Max Priority Scan	69
Viewing the Firmware Version and Electronic Serial Number	70
Initializing the Scanner’s Memory	70
Connecting Your Scanner to a Personal Computer	70
Volume/Squelch with PC Control	71
Wired Cloning	71
Start of Transfer	72
During Transfer	72
Programming Your Scanner	73
General Notes	73
System Settings	73
System Options	74
Site Option Settings	75
Channel Option Settings	75
Programming Conventional Systems	76
Programming Trunked Radio Systems	76
Programming System Settings	77
Editing the System Name	77
Specifying the Correct System Type	78
Editing the System Name	78
Programming System Options	78
Editing the System Quick Key	78
Setting the Startup Key	79
Setting the System Lockout	79
Setting the System Hold Time	80
Setting ID Scan/ID Search	80
Setting Channel Delay Time	80
Setting Data Skip	80
Setting Location Information	81
Setting the Fleet Map	81
Setting the Status Bit	82
Setting End Code Operation	82
Setting I-Call Operation	82
Setting the Emergency Alert Option	83
Assigning a Conventional System to a State	83
Conventional Systems	83
Setting the EDACS ID Format	84
Setting the System Record Option	84
Reviewing ID Search Lockouts	84
Clearing All Locked Out ID’s	85
Editing Sites	85
Editing Channel Groups	85
Copying Systems	85
Deleting Systems	86
Programming Sites	86
Setting the Site Name	86
Setting the Site Quick Key	87
Setting the Site Startup Key	87
Setting Site Frequencies	88
Setting Site Modulation	88
Setting Site Attenuation	89
Setting Site Lockout	89
Setting Site Hold Time	90
Editing the Band Plan	90
Setting Control-Channel Only Mode	91
Setting Site Location Information	91
Assigning a Trunked System to A State	91
Trunked Systems (Sites)	92
Deleting Sites	92
Programming Channel Groups	92
Setting Up a Channel Group	92
Editing a Channel Group Name	92
Setting the Group Quick Key	93
Editing Channels	93
Locking Out Channel Groups	93
Deleting Channel Groups	94
Programming Channels	94
Creating a Channel	94
Editing the Channel Name (Alpha Tag)	94
Editing Frequencies	95
Editing the Talk Group ID	95
Selecting CTCSS/DCS Tones	96
Quick CTCSS/DCS Save	96
Setting Channel Modulation Method	97
Setting Channel Attenuation	97
Setting Channel Priority	98
Setting Channel Alert	98
Setting Channel Record	99
Setting Lockout	99
Copying a Channel	99
Deleting a Channel	100
Searching and Storing	101
Service Search	101
Quick Search	102
Custom Search	102
Editing a Custom Search Range	103
Search With Scan	104
Editing a Service Search	105
Method One	105
Method Two	105
Set Delay Time	105
Set Attenuator	106
Set Record	106
Assigning a Search Range to a Search Key	106
Saving a Found Channel (Quick Save)	106
Auto Search and Store	107
Selecting a System	107
Conventional Search and Store	107
Trunked Search and Store	108
Using the Close Call Feature	109
Setting Close Call Options	109
Close Call Hits	111
Close Call Hits with Scan	111
Search and Close Call Options	113
Managing Locked-Out Frequencies	113
Unlocking All Frequencies	114
Reviewing Locked Out Frequencies	114
Searching for Subaudible Tones	114
Screening Out Broadcast Sources	115
Finding Repeater Output Frequencies	116
Setting the Maximum Auto Store Value	116
Setting the Modulation Type	116
Setting Attenuation	117
Setting Data Skip	117
Setting the Delay Time	118
Setting the Search Frequency Step	118
Setting Record	118
Priority Scan	119
Using Weather Alert (SAME)	120
Searching For a Weather Broadcast	120
Turning Weather Scan Alert On/Off	120
Programming a SAME Group	121
Setting WX Alert Priority	122
Fire Tone-Out Introduction	123
Setting Tone-Out Standby	123
Setting Up Tone-Out	123
Tone-Out Multi-Channel Monitoring	125
Setting Tone-Out Record	125
Using the BCT15 with a GPS	126
Device Compatibility	126
Connecting Your Scanner to a GPS Device	126
Initial Scanner/GPS Operation	126
Location-Based (GPS) Scanning	127
Another Example of Multiple Site Creation	128
Non-Radio Location Based GPS Features	128
Setting the Options	130
Deleting a Location	130
For POI Only	131
For Dangerous Xing, and Dangerous Road Only	131
GPS Display Mode	133
GPS Review Location Mode	134
Care and Maintenance	135
General Use	135
Location	135
Cleaning	135
Repairs	135
Birdies	135
Troubleshooting	136
Specifications	140
Reference	143
Preset Fleet Maps	143
User Defined Fleet Maps	145
Type I Programming Information	145
Size Code Restrictions	146
Index	147
One-Year Limited Warranty	150