Yamaha AW4416 Version2.0 Manual Supplement - Page 45

FORMAT No. 01111110 7E 01001100 4C 01001101 4D 00100000 20 00100000 20 00111000 38 01000011 42 00110011 39 00110110 38 DATA NAME 01000011 43 00100000 20 EOX 11110111 F7 Universal Bulk Dump 'L' 'M' ' ' ' ' '8' 'B' '9' '8' 'C' ' ' End Of Exclusive 4.13.3 Parameter Change 4.13.3.1 Basic format STATUS 11110000 F0 ID No. 01000011 43 SUB STATUS 0pppnnnn pn GROUP ID 00111110 3E MODEL ID 00001000 08 PARAM TYPE 0ttttttt tt DATA 0ddddddd dd0 : : 0ddddddd ddn EOX 11110111 F7 System Exclusive Message Manufacturer's ID (YAMAHA) p=mode (1:parameter change or response for request 3:parameter request) n=0-15(Rx Channel No.1-16) MODEL ID(Digital Mixer) Device Code(AW4416) Parameter type data 0 data n End Of Exclusive Parameter type rx/tx function 0x00 rx/tx edit buffer (byte operation format) 0x01 rx/tx setup memory (byte operation format) 0x02 rx/tx function call (mem/lib recall,mem/lib store) 0x10 rx/tx edit buffer (7bit operation format) 0x40 rx/tx edit buffer (bit operation format) 0x41 rx/tx setup memory (bit operation format) 0x43 rx/tx controller (key remote) (bit opera- tion format) 4.13.3.2 Parameter Change (byte operation for type 0x00:edit buffer) 4.13.3.2 < Reception > This message is received if [Parameter Change RX] is ON and the [Rx CH] matches the MIDI channel included in the Sub Status. This message will be echoed if [Parameter Change ECHO] is ON. When this message is received, the specified parameter will be controlled. < Transmission > If [Parameter Change TX] is ON, this message will be transmitted on the [Tx CH] MIDI channel when a param- eter not specified in the [Control Change Assign Table] is edited. This message will be echoed if [Parameter Change ECHO] is ON. STATUS 11110000 F0 System Exclusive Message ID No. 01000011 43 Manufacturer's ID No. (YAMAHA) SUB STATUS 0001nnnn 1n parameter change or response n=0-15(MIDI Channel No.1-16) GROUOP ID 00111110 3e MODEL ID(digital mixer) MODEL ID 00001000 08 Device code (AW4416) PARAM TYPE 00000000 00 byte operation for edit buffer (type) DATA 0aaaaaaa dd1 address( H) high 7 bits of 14 bits address 0aaaaaaa dd2 address( L) low 7 bits of 14 bits address 0000dddd dd3 data( H) high 4 bits of 8 bits data 0000dddd dd4 data( L) low 4 bits of 8 bits data : : continuous address datas EOX 11110111 F7 End Of Exclusive The range of valid addresses is 0x0000 - 0x0595. 4.13.3.3 Parameter Change (7bit operation for type 0x10:edit buffer) < Reception > This message is received if [Parameter Change RX] is ON and the [Rx CH] matches the MIDI channel included in the Sub Status. This message will be echoed if [Parameter Change ECHO] is ON. When this message is received, the specified parameter will be controlled. < Transmission > If [Parameter Change TX] is ON, this message will be trans- mitted on the [Tx CH] MIDI channel when a parameter not specified in the [Control Change Assign Table] is edited. This message will be echoed if [Parameter Change ECHO] is ON. STATUS 11110000 F0 System Exclusive Message ID No. 01000011 43 Manufacturer's ID No. (YAMAHA) SUB STATUS 0001nnnn 1n parameter change n=0- 15(MIDI Channel No.1-16) GROUOP ID 00111110 3e MODEL ID(digital mixer) MODEL ID 00001000 08 Device code (AW4416) PARAM TYPE 00010000 10 7bit operation for edit buffer (type) DATA 0aaaaaaa dd0 address( H) high 7 bits of 14 bits address 0aaaaaaa dd1 address( L) low 7 bits of 14 bits address 0ddddddd dd2 data 7bit : : EOX 11110111 F7 End Of Exclusive The range of valid addresses is 0x0000 - 0x0595. 4.13.3.4 Parameter Change (bit operation for type 0x40:edit buffer) < Reception > This message is received if [Parameter Change RX] is ON and the [Rx CH] matches the MIDI channel included in the Sub Status. This message will be echoed if [Parameter Change ECHO] is ON. When this message is received, the specified parameter will be controlled. < Transmission > If [Parameter Change TX] is ON, this message will be trans- mitted on the [Tx CH] MIDI channel when a parameter not specified in the [Control Change Assign Table] is edited. This message will be echoed if [Parameter Change ECHO] is ON. STATUS 11110000 F0 System Exclusive Message ID No. 01000011 43 Manufacturer's ID No. (YAMAHA) SUB STATUS 0001nnnn 1n parameter change n=0- 15(MIDI Channel No.1-16) GROUOP ID 00111110 3e MODEL ID(digital mixer) MODEL ID 00001000 08 Device code (AW4416) PARAM TYPE 01000000 40 bit operation for edit buffer (type) DATA 0aaaaaaa dd0 address( H) high 7 bits of 14 bits address 0aaaaaaa dd1 address( L) low 7 bits of 14 bits address 0ddddddd dd2 data(bit0-2:change bit no.0-7, bit3:0=reset 1=set) : : EOX 11110111 F7 End Of Exclusive The range of valid addresses is 0x0000 - 0x0595. Version 2.0 Manual Supplement 45