Yamaha AW4416 Version2.0 Manual Supplement - Page 47
Parameter Change, type 0x43:controllerkey remote, < Reception >, < Transmission >
View all Yamaha AW4416 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 47 highlights
function number channel Tx/Rx 0x00 scene recall 0-96(memory 0-96) 0x00 Tx* /Rx 0x01 eq lib recall 0-127(library 1-128) 0-26,32-47 Tx/Rx 0x02 dyn lib recall 0-127(library 1-128) 0-23,26,32-47 Tx/Rx 0x03 eff lib recall 0-127(library 1-128) 24,25 Tx/Rx 0x04 ch lib recall 0-64(library 0-64) 0-26,32-47 Tx/Rx 0x05 patch lib recall 0-20(library 0-20) 0 Tx/Rx 0x10 scene store 1-96(memory 1-96) 0x00 Rx only 0x11 eq lib store 40-127(library 41-128) 0-26,32-47 Rx only 0x12 dyn lib store 40-127(library 41-128) 0-23,26,32-47 Rx only 0x13 eff lib store 41-127(library 42-128) 24,25 Rx only 0x14 ch lib store 2-64(library 2-64) 0-26,32-47 Rx only 0x15 patch lib store 1-20(library 1-20) 0 Rx only Channel 0-7(INPUT 1-8), 8-23(MONITOR 1-16), 24,25(RTN 1-2/EFF 1-2), 26(st mas) * [0x00: scene recall] is transmitted only when you recall a program that has not been assigned in the [Program change table]. Normally a program change will be transmitted. 4.13.3.9 Parameter Change (type 0x43:controller(key remote)) < Reception > This message is received if [Parameter Change RX] is ON and the [Rx CH] matches the MIDI channel included in the Sub Status. This message will be echoed if [Parameter Change ECHO] is ON. When this message is received, the same processing will be performed as when the specified key (see table below) is pressed (released) < Transmission > This message will be echoed if [Parameter Change ECHO] is ON. STATUS 11110000 F0 System Exclusive Message ID No. 01000011 43 Manufacturer's ID No. (YAMAHA) SUB STATUS 0001nnnn 1n parameter change n=0- 15(MIDI Channel No.1-16) GROUOP ID 00111110 3e MODEL ID(digital mixer) MODEL ID 00001000 08 Device code (AW4416) PARAM TYPE 01000011 43 controller DATA 00000000 00 control no.(0:key remote) 0ddddddd dd No. 0-17(key 1-18) 0000dddd dd data(bit0-2:change bit no.0-7, bit3:0=reset 1=set) : : EOX 11110111 F7 End Of Exclusive KEY key no. rx/tx bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 key1 0 rx SONG VIEW AUX5 SHIFT-L BANK SEL1 SEL9 ON1 key2 1 rx ON9 ABS CUE SAFE JOGON NUM REPEAT REW key3 2 rx QUICK PAN AUX6 F1 PAD1 SEL2 SEL10 ON2 key4 3 rx ON10 PEAK REC1 REC9 UNDO MARK< A key5 4 rx MASTER EQ AUX7 F2 PAD2 SEL3 SEL11 ON3 key6 5 rx ON11 TRACK REC2 REC10 REDO MARK> B FF key7 6 rx CD DYN AUX8 F3 PAD3 SEL4 SEL12 ON4 key8 7 rx ON12 EDIT REC3 REC11 UP MARK ROLL key9 8 rx SETUP AUX1 HOME F4 PAD4 SEL5 SEL13 ON5 key10 9 rx ON13 A-MIX REC4 REC12 DOWN PUNCH TOP STOP key11 10 rx FILE AUX2 1-16 F5 PAD5 SEL6 SEL14 ON6 key12 11 rx ON14 SCENE REC5 REC13 LEFT IN RTZ key13 12 rx UTILITY AUX3 17-24 SHIFT-R PAD6 SEL7 SEL15 ON7 key14 13 rx ON15 STORE REC6 REC14 RIGHT OUT END PLAY key15 14 rx MIDI AUX4 MONI PAD7 SEL8 SEL16 ON8 key16 15 rx ON16 SCENE- REC7 REC15 ENTER SET CANCEL key17 16 rx HIGH HI-MID LOW-MID LOW PAD8 ASSIGN SEL-ST FOOT SW key18 17 rx ON-ST SCENE+ REC8 REC16 SOLO RECALL ST REC You must transmit Reset (bit 3=0) after transmitting Set (bit 3=1). Version 2.0 Manual Supplement 47