Yamaha CVP-601 Owner's Manual - Page 98

Assembly, Preparation Before Assembling

Get Yamaha CVP-601 PDF manuals and user guides View all Yamaha CVP-601 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Assembly Preparation Before Assembling CAUTION • Assemble the stand on a flat floor with ample space. • Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage. • Be sure to tighten up all screws upon completing assembly of each unit. • To disassemble, reverse the assembly sequence given below. Have a Phillips-head (+) screwdriver of the appropriate size ready. Assembly parts 6 x 20 mm long screws x 4 Cord holders x 2 4 x 20 mm tapping screws x 4 6 x 16 mm short screws x 6 Power cord Headphone hanger 4 x 12 mm thin screws x 2 Headphone hanger 4 x 10 mm thin screws x 2 Holder set For details on how to set the holders, refer to page 94. Remove foamed styrol pads from the package, position them on the floor, then place A on top of them. Position the pads so that they will not hide the connectors on the bottom of A. Remove all parts from the box. Confirm that all parts shown in the illustration are provided. Main Unit A Back panel Foamed styrol pads B Assembly 1 Attach C to D and E.  Untie and straighten out the bundled pedal cord. Do not discard the vinyl tie. You will need it later in step 5.  Attach D and E to C by tightening four long screws (6 x 20 mm). Pedal Box Bundled pedal cord inside C D  C E Side panel (left) Side panel(right) D E  Assembly 98 CVP-601 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
CVP-601 Owner’s Manual
98
Assembly
Assembly
CAUTION
•
Assemble the stand on a flat floor with ample space.
•
Be careful not to confuse parts, and be sure to install all parts in
the correct direction. Please assemble in accordance with the
sequence given below.
•
Assembly should be carried out by at least two persons.
•
Be sure to use the correct screw size, as indicated below. Use of
incorrect screws can cause damage.
•
Be sure to tighten up all screws upon completing assembly of
each unit.
•
To disassemble, reverse the assembly sequence given below.
Remove foamed styrol pads from the package, position
them on the floor, then place A on top of them. Position
the pads so that they will not hide the connectors on the
bottom of A.
Remove all parts from the box. Confirm that all parts shown
in the illustration are provided.
1
Attach C to D and E.
1
Untie and straighten out the bundled pedal cord.
Do not discard the vinyl tie. You will need it later
in step 5.
2
Attach D and E to C by tightening four long
screws (6 x 20 mm).
P
reparation Before Assembling
Have a Phillips-head (+) screwdriver of the appropriate
size ready.
A
B
C
D
E
Foamed styrol pads
Main Unit
Back panel
Pedal Box
Bundled pedal cord inside
Side panel (left)
Side panel(right)
Holder set
For details on how to set the holders, refer to page 94.
Assembly
6 x 20 mm long screws x 4
6 x 16 mm short screws x 6
4 x 12 mm thin screws x 2
4 x 20 mm tapping screws x 4
Cord holders x 2
Power cord
Headphone hanger
Headphone hanger
4 x 10 mm thin screws x 2
Assembly parts
C
D
E
2
1