Yamaha CVP-601 Owner's Manual - Page 99

Attach B., Mount A., Secure A., Connect the pedal cord and power cord., seen from the front.

Get Yamaha CVP-601 PDF manuals and user guides View all Yamaha CVP-601 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

2 Attach B.  Align the screw holes on the upper side of B with the bracket holes on D and E, then attach the upper corners of B to D and E by fingertightening two thin screws (4 x 12 mm).  Secure the bottom end of B using four tapping screws (4 x 20 mm).  Securely tighten the screws on the top of B that were attached in step 2- . E   A A  B D  3 Mount A. CAUTION • Be extra careful not to drop or let your fingers be pinched by the main unit. • Do not hold the main unit in any position other than the position specified. Be sure to place your hands at least 15cm from either end of the main unit when positioning it. Align the screw holes 5 Connect the pedal cord and power cord.  Insert the plug of the pedal cord into the pedal connector.  Attach the cord holders to the rear panel as shown, then clip the cord into the holders.  Use a vinyl tie to take up any slack in the pedal cord.  Insert the plug of the power cord into the power connector. Insert the pedal cord securely until the metal part of the cord plug disappears from view. Otherwise, the pedal may not function properly.  A Assembly 15cm or further in 4 Secure A.  Adjust the position of A so that the left and right  ends of A will project beyond D and E equally (as seen from the front).  Secure A by tightening six short screws (6 x 16 mm) from the front.   CVP-601 Owner's Manual 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
CVP-601 Owner’s Manual
99
Assembly
2
Attach B.
1
Align the screw holes on the upper side of B with
the bracket holes on D and E, then attach the
upper corners of B to D and E by finger-
tightening two thin screws (4 x 12 mm).
2
Secure the bottom end of B using four tapping
screws (4 x 20 mm).
3
Securely tighten the screws on the top of B that
were attached in step 2-
1
.
3
Mount A.
Be sure to place your hands at least 15cm from
either end of the main unit when positioning it.
4
Secure A.
1
Adjust the position of A so that the left and right
ends of A will project beyond D and E equally (as
seen from the front).
2
Secure A by tightening six short screws (6 x 16
mm) from the front.
5
Connect the pedal cord and power cord.
1
Insert the plug of the pedal cord into the pedal
connector.
2
Attach the cord holders to the rear panel as
shown, then clip the cord into the holders.
3
Use a vinyl tie to take up any slack in the pedal
cord.
4
Insert the plug of the power cord into the power
connector.
CAUTION
•
Be extra careful not to drop or let your fingers be
pinched by the main unit.
•
Do not hold the main unit in any position other than the
position specified.
2
13
E
B
D
A
Align the screw holes
15cm or further in
Insert the pedal cord securely
until the metal part of the cord
plug disappears from view.
Otherwise, the pedal may not
function properly.
1
2
A
A
1
2
3
4