Home » Brother International Manuals » Multifunction Devices » Brother International MFC-9340CDW » Manual Viewer

Brother International MFC-9340CDW Advanced Users Manual - English - Page 41

Remote retrieval, Setting a Remote Access Code

View all Brother International MFC-9340CDW manuals

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Receiving a fax Remote retrieval 4 You can call your machine from any touchtone telephone or fax machine and then use the remote access code and remote commands to retrieve fax messages. Setting a Remote Access Code 4 The Remote Access Code lets you access the remote retrieval features when you are away from your machine. Before you can use the remote access and retrieval features, you must set up your own code. The factory default code is the inactive code (- - -l). a Press . b Press All Settings. c Swipe up or down, or press a or b to display Fax. d Press Fax. e Swipe up or down, or press a or b to display Remote Access. f Press Remote Access. g Enter a three-digit code using the numbers 0 to 9, * or # using the keyboard on the Touchscreen. Press OK. (The preset 'l' cannot be changed.) NOTE DO NOT use the same code used for your Fax Receive Code (l51) or Telephone Answer Code (#51) (see Basic User's Guide: Using Remote Codes). h Press . NOTE You can change your code at any time. To make your code inactive, press and hold at step g to restore the inactive setting - - -l, and then press OK. Using your Remote Access Code 4 a Dial your fax number from a telephone 4 or another fax machine using touch tone. b When your machine answers, immediately enter your Remote Access Code (3 digits followed by l). c The machine signals if it has received messages:  1 long beep -- Fax messages  No beeps -- No messages d When the machine gives two short beeps, enter a command (see Remote fax commands on page 34). The machine will hang up if you wait longer than 30 seconds to enter a command. The machine will beep three times if you enter an invalid command. e Press 9 0 to reset the machine when you are finished. f Hang up. NOTE • If your machine is set to Manual mode and you want to use the remote retrieval features, wait for about 100 seconds after it starts ringing, and then enter the remote access code within 30 seconds. • This function may not be available in some countries or supported by your local telephone company. 33

Section	Page
Advanced User’s Guide MFC-9130CW/MFC-9330CDW/MFC-9340CDW	1
User’s Guides and where do I find them?	2
Table of Contents	4
1 General Setup	9
Memory storage	9
Volume settings	9
Ring volume	9
Beeper volume	10
Speaker volume	10
Automatic Daylight Saving Time	11
Ecology features	11
Toner Save	11
Sleep Time	12
Deep Sleep mode	12
Touchscreen	13
Setting the backlight brightness	13
Setting the Dim Timer for the backlight	13
Dial Prefix	14
Setting up the prefix number	14
Changing the prefix number	14
2 Security features	15
Secure Function Lock 2.0	15
Before you begin to use Secure Function Lock 2.0	16
Setting and changing the Administrator Password	16
Setting the administrator password	16
Changing the administrator password	16
Setting up restricted users	17
Setting up and changing the Public user mode	17
Turning Secure Function Lock on/off	18
Turning Secure Function Lock on	18
Turning Secure Function Lock off	18
Switching Users	19
Changing to the restricted user mode	19
Changing to the Public mode	19
Setting Lock	20
Setting up the administrator password	20
Changing the Setting Lock administrator password	21
Turning Setting Lock on/off	21
Turning Setting Lock on	21
Turning Setting Lock off	21
Restricting dialing	22
Dial pad restriction	22
Address Book restriction	22
Shortcuts restriction	22
3 Sending a fax	23
Additional sending options	23
Sending faxes using multiple settings	23
Changing a 2-sided fax layout (MFC-9340CDW)	24
Contrast	25
Changing Fax Resolution	25
Additional sending operations	26
Sending a fax manually	26
Manual transmission	26
Sending a fax at the end of a conversation	26
Dual access	27
Broadcasting	27
Before you begin the broadcast	27
How to broadcast a fax	27
Canceling a Broadcast in progress	28
Real Time Transmission	29
Overseas Mode	29
Delayed Fax	30
Delayed batch transmission	30
Checking and canceling waiting jobs	31
Setting your changes as the new default	31
Restoring all fax settings to the factory settings	32
Saving fax options as a Shortcut	32
Electronic cover page	33
Composing your own comments	33
Send a cover page for the next fax	34
Using a printed cover page	34
Destination Display	35
Polling	36
Polled transmit	36
Setup for polled transmit	36
4 Receiving a fax	37
Memory Receive Options	37
Fax Forwarding	37
Paging	38
Fax Storage	39
Changing Memory Receive Options	39
If received faxes have already been printed	39
If unprinted faxes are in the memory	39
Turning off Remote Fax Options	40
Remote retrieval	41
Setting a Remote Access Code	41
Using your Remote Access Code	41
Remote fax commands	42
Retrieving fax messages	43
Changing the Fax Forwarding number	43
Additional receiving operations	44
Printing a reduced incoming fax	44
2-sided printing for Fax mode (MFC-9330CDW and MFC-9340CDW)	44
Setting the Fax Receive Stamp	45
Receiving a fax at the end of a conversation	45
Setting the Print Density	46
Printing a fax from the memory	46
Receiving faxes into memory when the paper tray is empty	47
Polling	48
Polling receive	48
Sequential polling	48
Stop Polling	49
Canceling a Sequential Polling Job	49
5 Dialing and storing numbers	50
Telephone line services	50
Tone or Pulse (Canada only)	50
For Fax/Tel mode only	50
Special line considerations	50
Roll over telephone lines	50
Two-line telephone system	50
Converting telephone wall outlets	51
Installing machine, external two-line TAD and two-line telephone	51
Additional dialing operations	52
Dialing access codes and credit card numbers	52
Additional ways to store numbers	53
Storing Address Book numbers from Outgoing Calls	53
Setting up Groups for Broadcasting	53
Changing a Group name	54
Deleting a Group	54
Adding or deleting Group members	55
6 Printing reports	56
Fax reports	56
Transmission Verification Report	56
Fax Journal (Activity Report)	56
Reports	57
How to print a report	58
7 Making copies	59
Copy settings	59
Stop copying	59
Improving copy quality	59
Enlarging or reducing copies	60
2-sided Copying (MFC-9330CDW and MFC-9340CDW)	61
Adjusting Density and Contrast	63
Density	63
Contrast	63
Sorting copies	64
Making N in 1 copies (page layout)	64
If you are copying from the ADF:	65
If you are copying from the scanner glass:	65
2 in 1 ID Copy	66
Adjusting the Color Saturation	67
Making 2-sided N in 1 copies (MFC-9340CDW)	67
Removing Background Color	68
Saving copy options as a Shortcut	69
Saving paper	69
A Routine maintenance	70
Cleaning and checking the machine	70
Cleaning the outside of the machine	71
Cleaning the LED heads	72
Cleaning the scanner	73
Cleaning the corona wires	75
Cleaning the drum unit	78
Cleaning the paper pick-up rollers	84
Calibration	85
Auto Registration	86
Frequency (Color Correction)	86
Printing the test print	87
Checking the Page Counters	87
Checking the remaining life of toner cartridges	88
Checking the remaining life of parts	88
Replacing periodic maintenance parts	89
Packing and shipping the machine	90
B Glossary	92

Match case Limit results 1 per page

Receiving a fax

Remote retrieval

You can call your machine from any touch-

tone telephone or fax machine and then use

the remote access code and remote

commands to retrieve fax messages.

Setting a Remote Access

Code

The Remote Access Code lets you access

the remote retrieval features when you are

away from your machine. Before you can use

the remote access and retrieval features, you

must set up your own code. The factory

default code is the inactive code (– – –

Press

All Settings

Swipe up or down, or press

display

Fax

Press

Fax

Swipe up or down, or press

display

Remote Access

Press

Remote Access

Enter a three-digit code using the

numbers

using the

keyboard on the Touchscreen.

Press

(The preset ‘

’ cannot be changed.)

NOTE

DO NOT use the same code used for your

Fax Receive Code (

) or Telephone

Answer Code (

#51

) (see

Basic User's Guide:

Using Remote

Codes

Press

NOTE

You can change your code at any time. To

make your code inactive, press and hold

at step

to restore the inactive

setting – – –

, and then press

Using your Remote Access

Code

Dial your fax number from a telephone

or another fax machine using touch

tone.

When your machine answers,

immediately enter your Remote Access

Code (3 digits followed by

The machine signals if it has received

messages:



1 long beep -- Fax messages



No beeps -- No messages

When the machine gives two short

beeps, enter a command (see

Remote

fax commands

on page 34). The

machine will hang up if you wait longer

than 30 seconds to enter a command.

The machine will beep three times if you

enter an invalid command.

Press

to reset the machine when you

are finished.

Hang up.

NOTE

•

If your machine is set to

Manual

mode

and you want to use the remote retrieval

features, wait for about 100 seconds after

it starts ringing, and then enter the remote

access code within 30 seconds.

•

This function may not be available in some

countries or supported by your local

telephone company.