Brother International NX-250 Users Manual - English - Page 106

Error messages

Get Brother International NX-250 PDF manuals and user guides View all Brother International NX-250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

Symptom Probable Cause The feed dogs are lowered. The fabric does not feed. The stitch is too short. The presser foot that is used is not appropriate for the type of stitch that you wish to sew. The pressure of the presser foot is weak. The thread is tangled, for example, in the bobbin case. The sewing lamp does not come on. The sewing lamp is damaged. Remedy Slide the drop feed lever to the right (as seen from the rear of the machine). Lengthen the stitch length. Attach the presser foot that is appropriate for the type of stitch that you wish to sew. Turn the presser foot pressure dial to the left to increase the pressure of the presser foot. Remove the tangle thread. If the thread is tangled in the bobbin case, clean the race. Contact your dealer or the nearest authorized service center. Reference page 69, 82 page 48 page 94 page 34 page 100 - Error messages If ("Start/Stop" button) is pressed before the sewing machine is correctly set up or if an operation is performed incorrectly, an error message appears in the stitch indicator. Follow the instructions that appear. 4 The message may disappear if the operation is performed correctly. The message will disappear if or (Stitch selection keys) is pressed while the message is displayed. Error Message Probable Cause The "Start/Stop" button or "Reverse/Reinforcement Stitch" button was pressed while the presser foot was raised. A stitch other than the buttonhole or bar tack stitch was selected and the "Start/Stop" button was pressed while the buttonhole lever is lowered. The buttonhole or bar tack stitch was selected and the "Start/Stop" button was pressed while the buttonhole lever is raised. The "Reverse/Reinforcement Stitch" button or "Needle Position" button was pressed while the bobbin winder is moved to the right. The "Start/Stop" button was pressed while the foot controller was connected. The motor locked up because the thread is tangled. The needle mode selection key was pressed while a stitch that cannot be used with twin needle sewing was selected. You tried to select a different stitch while the twin needle sewing setting was selected (the key is lit). Troubleshooting 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Troubleshooting
105
4
Error messages
If
(“Start/Stop” button) is pressed before the sewing machine is correctly set up or if an operation is
performed incorrectly, an error message appears in the stitch indicator. Follow the instructions that appear.
The message may disappear if the operation is performed correctly. The message will disappear if
or
(Stitch selection keys) is pressed while the message is displayed.
The fabric does
not feed.
The feed dogs are lowered.
Slide the drop feed lever to the right
(as seen from the rear of the machine).
page 69, 82
The stitch is too short.
Lengthen the stitch length.
page 48
The presser foot that is used is not
appropriate for the type of stitch that
you wish to sew.
Attach the presser foot that is
appropriate for the type of stitch that
you wish to sew.
page 94
The pressure of the presser foot is
weak.
Turn the presser foot pressure dial to
the left to increase the pressure of
the presser foot.
page 34
The thread is tangled, for example,
in the bobbin case.
Remove the tangle thread. If the
thread is tangled in the bobbin case,
clean the race.
page 100
The sewing lamp
does not come on.
The sewing lamp is damaged.
Contact your dealer or the nearest
authorized service center.
–
Error Message
Probable Cause
The “Start/Stop” button or “Reverse/Reinforcement
Stitch” button was pressed while the presser foot was
raised.
A stitch other than the buttonhole or bar tack stitch was
selected and the “Start/Stop” button was pressed while
the buttonhole lever is lowered.
The buttonhole or bar tack stitch was selected and the
“Start/Stop” button was pressed while the buttonhole
lever is raised.
The “Reverse/Reinforcement Stitch” button or “Needle
Position” button was pressed while the bobbin winder is
moved to the right.
The “Start/Stop” button was pressed while the foot
controller was connected.
The motor locked up because the thread is tangled.
The needle mode selection key was pressed while a
stitch that cannot be used with twin needle sewing was
selected.
You tried to select a different stitch while the twin
needle sewing setting was selected (the key is lit).
Symptom
Probable Cause
Remedy
Reference