Cisco SRW224G4P User Guide - Page 65

Standard ACL, Extended ACL

Get Cisco SRW224G4P - Small Business Managed Switch PDF manuals and user guides
UPC - 745883578535
View all Cisco SRW224G4P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet Standard ACL To configure a standard ACL do the following. Specify the action (that is, Permit or Deny). Select the address type (Any, Host, or IP). If you select "Host," enter a specific address. If you select "IP," enter a subnet address and the mask for an address range. Then click Add. Extended ACL To configure an extended ACL do the following. Specify the action (that is, Permit or Deny). Specify the source and/or destination addresses. Select the address type (Any, Host, or IP). If you select "Host," enter a specific address. If you select "IP," enter a subnet address and the mask for an address range. Set any other required criteria, such as service type, protocol type, or TCP control code. Then click Add. Action. An ACL can contain any combination of permit or deny rules. Source Address/Destination Type. Specifies the source or destination IP address. Use "Any" to include all possible addresses, "Host" to specify a specific host address in the Address field, or "IP" to specify a range of addresses with the Address and SubMask fields. (Options: Any, Host, IP; Default: Any) Source/Destination IP Address. Source or destination IP address. Source/Destination Subnet Mask. Subnet mask for source or destination address. Service Type. Packet priority settings based on the following criteria: • Precedence - IP precedence level. (Range: 0-7) • TOS - Type of Service level. (Range: 0-15) • DSCP - DSCP priority level. (Range: 0-63) Figure 5-40: ACL Conf - Adding/Editing Standard ACL Figure 5-41: ACL Conf - Adding/Editing Extended ACL 57 Chapter 5: Configuring the Switch through the Web Utility Security

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
57
Chapter 5: Configuring the Switch through the Web Utility
Security
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Standard ACL
To configure a standard ACL do the following.
Specify the action (that is, Permit or Deny). Select the address type (Any, Host, or IP). If you select “Host,” enter a
specific address. If you select “IP,” enter a subnet address and the mask for an address range. Then click
Add
.
Extended ACL
To configure an extended ACL do the following.
Specify the action (that is, Permit or Deny). Specify the source and/or destination addresses. Select the address
type (Any, Host, or IP). If you select “Host,” enter a specific address. If you select “IP,” enter a subnet address and
the mask for an address range. Set any other required criteria, such as service type, protocol type, or TCP control
code. Then click
Add
.
Action
. An ACL can contain any combination of permit or deny rules.
Source Address/Destination Type
. Specifies the source or destination IP address. Use “Any” to include all
possible addresses, “Host” to specify a specific host address in the Address field, or “IP” to specify a range of
addresses with the Address and SubMask fields. (Options: Any, Host, IP; Default: Any)
Source/Destination IP Address
. Source or destination IP address.
Source/Destination Subnet Mask
. Subnet mask for source or destination address.
Service Type
. Packet priority settings based on the following criteria:
•
Precedence – IP precedence level. (Range: 0-7)
•
TOS – Type of Service level. (Range: 0-15)
•
DSCP – DSCP priority level. (Range: 0-63)
Figure 5-40: ACL Conf - Adding/Editing Standard ACL
Figure 5-41: ACL Conf - Adding/Editing Extended ACL