Compaq ML370 ProLiant ML370 Maintenance and Service Guide - Page 67

Error Code, Audible Beeps, Probable Source of Problem, Recommended Action, do not, SCSI: Port n

Get Compaq ML370 - ProLiant - 128 MB RAM PDF manuals and user guides
UPC - 720591236915
View all Compaq ML370 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Diagnostics and Troubleshooting 3-13 Table 3-2 POST Error Messages continued Error Code Audible Beeps 1702 - SCSI cable None error detected; system halted. 1703 - SCSI cable None error detected. Internal SCSI cable not attached to system board connector. System halted. 1720 - Slot x Drive None Array-SMART hard Drive Detects Imminent Failure SCSI: Port n: SCSI ID x 1721 - Slot x Drive None Array-Drive parameter tracking predicts imminent failure. The following devices should be replaced when conditions permit. Do not replace drive unless all other drives in the array are online! Back up data before replacing drive(s) if using RAID 0. Probable Source of Problem Termination or cabling problem with the system board integrated SCSI controller. Incorrect cabling Recommended Action Refer to cabling diagrams in Chapter 2 of this guide, the cabling guidelines on the Compaq website, and your Compaq server documentation. Ensure that the integrated SCSI controller has SCSI termination attached. Prefailure condition Monitor and performance threshold exceeded condition. Indicated drive has reported a SMART predictive-failure condition and may fail at some time in the future. If drive is part of a non-fault-tolerant configuration, back up all data before replacing drive and restore all data afterward. If drive is part of a fault-tolerant configuration do not replace the drive unless all other drives in the array are online. Press F1 to resume. Replace the drive when it is reasonable for you to do. The drive has not failed, but Compaq recommends you replace the drive. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Diagnostics and Troubleshooting
3-13
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1702 - SCSI cable
error detected;
system halted.
None
Termination or cabling problem
with the system board integrated
SCSI controller.
Refer to cabling diagrams in
Chapter 2 of this guide, the
cabling guidelines on the
Compaq website, and your
Compaq server documentation.
1703 - SCSI cable
error detected.
Internal SCSI cable
not attached to
system board
connector. System
halted.
None
Incorrect cabling
Ensure that the integrated SCSI
controller has SCSI termination
attached.
1720 - Slot x Drive
Array
—
SMART hard
Drive Detects
Imminent Failure
SCSI: Port n:
SCSI ID x
None
Prefailure condition
Indicated drive has reported a
SMART predictive-failure
condition and may fail at some
time in the future. If drive is part
of a non-fault-tolerant
configuration, back up all data
before replacing drive and
restore all data afterward. If
drive is part of a fault-tolerant
configuration
do not
replace the
drive unless all other drives in
the array are online. Press
F1
to
resume.
1721 - Slot x Drive
Array
—
Drive
parameter tracking
predicts imminent
failure. The following
devices should be
replaced when
conditions permit. Do
not replace drive
unless all other
drives in the array
are online! Back up
data before replacing
drive(s) if using
RAID 0.
None
Monitor and performance
threshold exceeded condition.
Replace the drive when it is
reasonable for you to do. The
drive has not failed, but Compaq
recommends you replace the
drive.
continued