Compaq ML370 ProLiant ML370 Maintenance and Service Guide - Page 73

Port y: SCSI ID x, Integrated Smart Array

Get Compaq ML370 - ProLiant - 128 MB RAM PDF manuals and user guides
UPC - 720591236915
View all Compaq ML370 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Diagnostics and Troubleshooting 3-19 Table 3-2 POST Error Messages continued Error Code Audible Beeps 1778 - Slot x Drive None Array resuming Automatic Data Recovery process 1779 - Slot x Drive None Array-replacement drives detected OR previously failed drive(s) now appear to be operational: Port (y): SCSI ID (x): Restore data from backup if replacement drive x has been installed. 1780 - Disk 0 Failure None 1781 - Disk 1 Failure None 1782 - Disk None Controller Failure 1783 - Slot x Drive None Array Controller Failure 1784 - Slot x Drive None Array Drive Failure. The following SCSI drive(s) should be replaced: SCSI port (y) SCSI ID (x). Probable Source of Problem This message appears whenever a controller reset or power cycle occurs while Automatic Data Recovery is in progress. Intermittent drive failure and/or possible loss of data Recommended Action No action required. This message appears whenever a controller reset or power cycle occurs while Automatic Data Recovery is in progress. If this message appears and drive x (identified by its SCSI ID) has not been replaced, this indicates an intermittent drive failure. This message also appears once immediately following drive replacement whenever data must be restored from backup. Hard drive/format error Hard drive/format error Hard disk drive circuitry error ROM installation problem or Array Accelerator board problem Defective drive and/or cables Run Diagnostics. Replace failed assembly as indicated. Run Diagnostics. Replace failed assembly as indicated. Run Diagnostics. Replace failed assembly as indicated. If this message appears immediately following a ROM installation, the ROM is defective or not installed properly. Check that the controller is firmly inserted in its slot. Try upgrading the System ROMs. Otherwise, replace the Integrated Smart Array Controller. Check for loose cables. Replace defective drive x and/or cable(s). continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Diagnostics and Troubleshooting
3-19
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1778 - Slot x Drive
Array resuming
Automatic Data
Recovery process
None
This message appears whenever
a controller reset or power cycle
occurs while Automatic Data
Recovery is in progress.
No action required. This
message appears whenever a
controller reset or power cycle
occurs while Automatic Data
Recovery is in progress.
1779 - Slot x Drive
Array
—
replacement
drives detected OR
previously failed
drive(s) now appear
to be operational:
Port (y): SCSI ID (x):
Restore data from
backup if
replacement drive x
has been installed.
None
Intermittent drive failure and/or
possible loss of data
If this message appears and
drive x (identified by its SCSI ID)
has not been replaced, this
indicates an intermittent drive
failure. This message also
appears once immediately
following drive replacement
whenever data must be restored
from backup.
1780 - Disk 0 Failure
None
Hard drive/format error
Run Diagnostics. Replace failed
assembly as indicated.
1781 - Disk 1 Failure
None
Hard drive/format error
Run Diagnostics. Replace failed
assembly as indicated.
1782 - Disk
Controller Failure
None
Hard disk drive circuitry error
Run Diagnostics. Replace failed
assembly as indicated.
1783 - Slot x Drive
Array Controller
Failure
None
ROM installation problem or
Array Accelerator board problem
If this message appears
immediately following a ROM
installation, the ROM is
defective or not installed
properly. Check that the
controller is firmly inserted in its
slot. Try upgrading the System
ROMs. Otherwise, replace the
Integrated Smart Array
Controller.
1784 - Slot x Drive
Array Drive Failure.
The following SCSI
drive(s) should be
replaced: SCSI
port (y) SCSI ID (x).
None
Defective drive and/or cables
Check for loose cables. Replace
defective drive x and/or
cable(s).
continued